Évaluations - 5, GPA: 3.8
(
)
)
|
Facilité d'utilisation
That’s all there is to it. //?\\\ niSKpii )l1=ll C^°og&°Jo SPECIFICATIONS Function Specification Power Supply Bus Powered Cable length (output) 5 m (16ft.) Connectors 1 Type A Male 1 Type A Female USB Specification 2.0 spec, for high, full and low Driver Support Native Driver Support Operating Temperature o o LO Storage Temperature o o CD o C\l Humidity 0% - 80% RH, NC Weight 255g S3 Trdubleshddting Problem Cause Solution Device operates erratically Static electricity or insufficient power may cause the device to operate erratically. Reset the device by unplugging the cable and then plugging it back in or use external power to your linked devices. -4- Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose. The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or update. For further inquiries, please contact your direct vendor. -5 - User Manual U E-25D Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit, and/or any of the devices connected to it. This package contains: ♦ 1 UE-250 USB 2.0 Repeater Cable ♦ 1 User Manual If anything is damaged or missing, contact your dealer. © Copyright 2003 ATEN® International Co., Ltd. Manual Part No. PAPE-1240-100 Printed in Taiwan 10/2003 All brand names and trademarks are the registered property of their respective owners. □ VERVIEW Components -1 - NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Subpart J of Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ♦ Reorient or relocate the receiving antenna. ♦ Increase the separation between the equipment and receiver. ♦ Connect the equipment into an outlet on a circuit different from that which the receiver is connected. ♦ Consult the dealer or an experienced radio/television technician for help. R£C€ The UE-250 USB Repeater Cable allows you to extend the distance between your computer and your USB peripherals by 5 meters (16’). Unlike typical cables, the UE-250 is an active extension cable. All USB signals transmitted through it are regenerated to maintain optimal signal integrity to meet the USB 2.0 specification. Features ♦ Extends the distance to USB devices by 5 m (16’) ♦ Embedded custom ASIC regenerates transmitted USB signals to maintain optimal signal integrity System Requirements ♦ Whistler; Windows: XP, 2000, Me, 98 SE; Mac OS 8.6 or higher Note: Only systems with a USB 2.0 driver installed can support data transfer speeds of up to 480 Mbps; all others only support speeds of up to 12 Mbps. ♦ USB 2.0 Host Controller installed on the system. Note: The UE-250 can be connected to a USB 1.1 Host Controller, but in that case, it only supports USB 1.1 speeds (1.5 -12 Mbps). -2 - 3 1. Built in cable with USB connection to USB port on PC or hub 2. LED (green) indicates USB link 3. Type A female USB port for connection from peripheral 4. LED (red) indicates overcurrent...