Évaluations - 5, GPA: 4 ( )

Fabricant : Adder Technology Taille : 149.68 kb Nom Fichier : 6d37f385-10fc-44d4-5935-31baff3d47b5.pdf Langue d'enseignement:

1. Connect the DB-9 (male) connector of your serial cable to the console port on the rear panel of the unit. 2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation software). 3. Open a VT100 terminal session to the Total Access 234 using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press to activate the ADTRAN Command Line Interface (CLI). SPECIFICATIONS DC Input Power 12 VDC nominal (8.5 VDC min, 18 VDC max); ITU-T standards: G.991.2 Diagnostics & Test Self-diagnosis; local loopback; remote loopback EMC Emissions EN55022:1998 Class B; FCC Part 15 Class B EMC Immunity, Power EN55024:1998; EN61000-3-2; EN61000-3-3; Telstra 1563; K.21 (2004) Fault, and Lightning Enhanced Electrical Safety EN60950; AS/NZS 60950; UL60950 3rd ed.; CSA C22.2 No. 60950 3rd ed.; IEC 60950 CB Scheme Telecom S043.2; G.991.2 Environmental Operating Temp: 0oC to 50oC; Storage Temp: -20oC to 70oC *Note: No stacking should be done at 50oC. Up to three units can be stacked at room temperature. Humidity: 95 percent noncondensing Dimensions 9.3 inches W x 2.1 inches H x 6.1 inches D Connectors SHDSL Port: RJ-45; 135 ohms; TNV-3 rated 10/100BaseT Ethernet: RJ-45 Console Port: DB-9 female Power Input: Kycon KPJ-3S snap & lock or equivalent CONFIGURE GATEWAY IP ADDRESSES/SUBNET MASK Configure the Gateway IP addresses and subnet mask by following these steps. If you are not sure what IP address to assign, please contact your network administrator. 1. Enter enable to activate the Enable command security mode. 2. When prompted, enter the enable password (if configured). 3. Enter config terminal to activate the Global configuration mode. 4. Enter bre lan-gw 10.26.12.12 wan-gw 100.26.12.12 mask 255.255.255.0* to assign LAN and WAN Gateway IP addresses and subnet mask. *Note: Underlined text represents example entries only. Modify them to match your configuration. 5. Enter exit to return to the Enable configuration mode. 6. Enter copy running-config startup-config to save the runningconfiguration to the unit’s non-volatile memory (NVRAM). FEATURES • One integrated EIA-232 configuration port (DCE) • One integrated 10/100BaseT Ethernet port • 2-Wire/4-Wire SHDSL interface • WAN Protocol: ATM • Command Line Interface (CLI) • Management - EOC/CLI using Virtual Terminal • Front panel LEDs • Wall mounting available with additional parts Table standoff cannot be used with this unit. Quick Start Guide, 61200708L1-13B, January 2005 Technical Support 1-888-4ADTRAN or +1-256-963-8716 Copyright © 2005 ADTRAN, All Rights Reserved For more detailed documentation, visit us online at Quick Start Guide TOTAL ACCESS 234 SHDSL NTU P/N 1200708L1 TOTAL ACCESS 234 LEDS 10/100BASET ETHERNET PORT PINOUT LED Color Indication PWR Off Green (solid) No power present. Power present. SHDSL Off Green (solid) Yellow (solid) Red (solid) Unit is powered off. Port is trained with no active alarm conditions. Port is trained with minor active alarm condition. Port is attempting to train or is trained with amajor alarm condition. LLOOP Off Red (solid) No local loop is active. A local loop is active. RLOOP Off Red (solid) No remote loop is active. A remote loop is active. BERT -Not applicable with this product. LNK Off Green (solid) Yellow (solid) No Ethernet link present. The 10BaseT Ethernet link is up. The 100BaseT Ethernet link is up. TD Off Green (blinking) No transmit activity on Ethernet port. Transmit activity on Ethernet port. RD Off Green (blinking) No receive activity on Ethernet port. Receive activity on Ethernet port. Pin Name Description 1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive 4,5 — Unused 6 RX2 Receive Negative 7,8 — Unused CONSOLE PORT PINOUT Pin Name Description 1 DCD Data Carrier Detect (output) 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR Data Terminal Ready (input) 5 SG Signal Ground 6 DSR Data Set Ready Tied to pin 1 (output) 7, 9 — Unused 8 CTS Clear to Send Tied to pin 1 (output) WAN-SHDSL NETWORK PINOUT (RJ-45) Pin Name Description 1 Tip 2 4-wire Loop 2 Pair Tip 2 Ring 2 4-wire Loop 2 Pair Ring 3 — Not connected 4 Tip 1 2-wire Pair Tip, 4-wire Loop 1 Pair Ring 5 Ring 1 2-wire Pair Ring, 4-wire Loop 1 Pair Ring 6-8 — Unused Quick Start Guide, 61200708L1-13B, January 2005 Technical Support 1-888-4ADTRAN or +1-256-963-8716 Copyright © 2005 ADTRAN, All Rights Reserved ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :