Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VR602BMG is illustrated here. The VR402BMG has single AUDIO IN/OUT jacks.) Disconnect the antenna or cable from your TV. 75V ANT / CABLE OR 75ANT / CABLE ANTENNA IN Jack (on back of TV) Cable Antenna Indoor/Outdoor (300 ohm) (75 ohm) 2 Connect the antenna or cable to the ANT(enna) IN Jack of your VCR. Back of VCR OR CH3 CH4 OUT IN ANT AUDIO R L VIDEO OUT IN INOUTCable (75 ohm) Antenna Indoor/Outdoor (300 ohm) Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.) 75V ANT / CABLE 75ANT / CABLE CH3 CH4 OUT IN ANT AUDIO R L VIDEO OUT IN INOUT RF coaxial cable Antenna or Cable ANTENNA IN Jack (on back of TV) example only 4 Plug in the TV and the VCR. 5 Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03. LCH 4orCH 3 CH3 CH4 OUT IN ANT CH3 / CH4 Switch CH3 CH4 AUDIO R L VIDEO OUT IN INOUT You are ready to turn on the VCR. Please go to page 11 before turning on the VCR. 8 Hookups With a Cable Box/Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: . You may view any channel. . You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. . You may not view a channel other than the one you are recording. . You may not program channels at the VCR. . You can only program a timer recording for one channel at a time. Set the TV and the VCR to the Cable Box/DBS output channel (channel 03 or 04); set the CH3/CH4 switch to the same channel. Set your Cable Box/DBS to the channel you want to record. When you enter the channel you want to record in a timer recording, select channel 03 or 04 (the Cable Box/DBS output channel). (This is step 5 on page 29.) Leave the Cable Box/DBS on for a timer recording. CH3 CH4 OUT IN ANT OUT IN 75ANT / CABLE TV’s ANTENNA IN Jack Cable Box/DBS VCR1 2 3 Cable Signal RF coaxial cable RF coaxial cable Connections 1 Connect a Cable signal to the IN Jack on the Cable Box/DBS. 2 Use an RF coaxial cable (supplied) to connect the OUT Jack on the Cable Box/DBS to the ANT(enna) IN Jack on the VCR. 3 Use a second RF coaxial cable to connect the OUT Jack on the VCR to the TV’s ANTENNA IN Jack. Recording/Viewing Any Channel 1 With the VCR on and in VCR position (the VCR Light will appear on the display panel), use the CHANNEL o/p buttons to set the VCR to the Cable Box/DBS output channel (channel 03 or 04). Set the CH3/CH4 switch to the same channel. 2 Set the TV to the same channel to which you set the VCR. 3 Select the channel you want to view/record at the Cable Box/DBS. CH3 CH4 OUT IN ANT IN OUT 75ANT / CABLE TV’s ANTENNA IN Jack Cable Box/DBS 1 2 3 Cable Signal RF coaxial cable RF coaxial cable TV’s ANTENNA IN Jack Cable Box/DBS 1 2 3 Cable Signal RF coaxial cable RF coaxial cable Hookups With a Cable Box/Direct Broadcast System (cont’d) 9 With this connection: l You may watch one channel while recording another. l You may not record scrambled channels. VCR Connections 1 Connect a Cable signal to the VCR’s ANT(enna) IN Jack. 2 Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack on the Cable Box/DBS. 3 Use a second RF coaxial cable to connect the OUT Jack on the Cable Box/DBS to the ANTENNA IN Jack on the TV. Recording One Channel/Watching Another 1 Put the Cable Box/DBS on the same channel as the VCR’s CH3/CH4 switch. Set the TV to the Cable Box/DBS output channel (03 or 04). Then, with the VCR in VCR position (the VCR Light will appear on the display panel), use the CHANNEL o/p buttons to select the channel you want to record at the VCR. Start the recording. 2 Press the VCR/TV button once to put the VCR in TV position. (The VCR Light will disappear.) 3 Select the channel you want to watch at the Cable Box/DBS. • When you play a tape, make sure the Cable Box/DBS is set to the same channel as the CH3/CH4 switch on the VCR. Set the TV to the Cable Box/DBS output channel (03 or 04). Helpful Hint 10 Hookups with a Stereo TV antenna or cable to ANT(enna) IN Jack Video Cable Stereo Audio Cable VIDEO (yellow) and AUDIO (red and white) OUT Jacks Audio and Video IN Jacks on TV 1 2 3 VR602BMG l Audio and Video cables are not supplied. VIDEO INOUT CH3 CH4 AUDIO OUT IN ANT antenna or cable to ANT(enna) IN Jack Video Cable VIDEO (yellow) and AUDIO (white) OUT Jacks 1 2 VR402BMG 3 Audio and Video IN Jacks on TV Audio Cable 1 Connect the antenna or cable to the ANT(enna) IN Jack on the back ...
Ce manuel est également adapté pour les modèles :Matériel de réseau - VR602BMG (673.66 kb)