Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
The selection cycle is SCART input 1> 2 > 3 > 4 4 Aim the remote control at the receiver unit to control the video source. 10 ENGLISH Problem solving If a fault occurs, first check the points listed below. If you are unable to remedy a problem by following these hints, contact the helpline (see ‘Need help?’) or consult your dealer. Never tr y to open the set yourself as this will void the guarantee. First, check all cables to ensure that they are connected correctly. Problem Solution No picture on TV3 • Ensure that both units are switched on (A-2 and B-20 are green). • Select the EXT or AV channel on TV3. • Activate the video source (set-top box: power on; VCR/DVD: playback). • Select the correct video source on the Receiver unit. • Select the same frequency channel on both the Receiver and Transmitter units. • If a VCR is the video source, ensure that the correct SCART connector of the VCR is used (Ext1 or Ext2 - check VCRs user manual). Bad picture/sound • Move the receiver unit around gently until you get good picture and quality on TV3 sound quality. • Move the transmitter unit around gently until you get good picture and sound quality. • Change both units to another frequency channel. • Reduce the distance between the transmitter and receiver unit (<30m). The cable • Disable the auto standby mode of the VCR. (Check VCR’s User Manual). programme you are watching disappears after several minutes Wrong picture on • Select the EXT or AV channel on TV3. TV3 • Select another video source on the receiver unit. • Activate the video source (set-top box: power on; VCR/DVD: playback). • Swap the SCART connectors on the transmitter unit. • Switch to another frequency channel on both units. Wrong picture on • Select the correct EXT or AV channel on TV1 TV1 (see TV instruction manual). • Select the correct video source with the VIEW SOURCE button (A-5). • Select a regular programme number. ENGLISH 11 No control of • Aim the remote control directly at the receiver unit and ensure that video sources there are no obstacles in between (B-19 must flash). from TV3 • Ensure that there is no other wireless device (wireless headphones, speakers, RF control signals) interfering with the remote control. • The maximum operating distance between the remote control and the receiver unit is 6 metres*; make sure you are within this range. • Ensure that the transmitter and receiver unit are more than 5 metres apar t. • Ensure that the remote control belonging to the video source is used to control it. • Reposition the remote control blaster cord light on the video source, or place the light 5-10 cm in front of the video source. Buzzing sound • Move the receiver unit around gently until the buzzing sound stops. when using the • Move the transmitter unit around gently until the buzzing sound stops. remote control • With some types of TV you will not be able to solve this problem. Easylink feature • Check that both your TV and VCR suppor t this feature doesn’t work (check TV and VCRs user manuals). • Use Easylink compatible or fully wired SCART cables. S-VHS video gives • Select CVBS video output format for your S-VHS VCR when using black and white SCART input 1 or 2 (check the VCRs user manual). pictures only DVD player gives • Connect the DVD player to SCART input 3 or 4 (both suppor t RGB). no pictures on • Select CVBS video output format for your DVD player TV1, TV2 or TV3 (check the DVD player’s user manual). * depends on remote control’s signal strength and batter y condition. 12 ENGLISH General notes • Picture and sound quality is influenced by the use of microwave ovens. Other wireless systems (Bluetooth, wireless LANs, etc.) can also adversely influence the quality of picture and sound, and vice versa. • The Wireless TV Link is a Radio Frequency (RF) based product. As such its performance can suffer the same kinds of interference as GSMs, por table radios and other RF-based products. • If the same video source is selected for both TVs, then you get the same programme on each TV. • The Wireless TV link is not limited to just one room or house. You can use it anywhere in or around the house. Consequently, anybody in the vicinity of your house (up to the maximum operating range) who also owns a Wireless TV link set to the same channel, can watch the same programmes that are playing on your video source. • In order to prevent the mixing of remote control commands it is not advisable to use a TV as a video source. • Some built-in VCRs (TV-VCR combination) cannot be used with the transmitter unit (depends on brand and type). • Video sources cannot be controlled remotely if the carrier frequency of the IR signal is outside the operation window of 32kHz to 57kHz. • Radio wave safety: When switched on, the Philips Wireless TV Link transmits and receives radio waves.The Philips Wireless TV Link complies with the standards that are defined for it. • The transmitter unit can suppor t the channel downloading feature (also known as ‘Follow-...
Ce manuel est également adapté pour les modèles :Matériel de réseau - SBCVL1405/00 (643.43 kb)