Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Network Protocol and Standards Compatibility Data and Routing Protocols TCP/IP Power Adapter North America 120V, 60 Hz, input ??? United Kingdom, Australia 240V, 50 Hz, input ??? Europe 230V, 50 Hz, input ??? Japan 100V, 50/60 Hz, input ??? All regions (output) 12 V DC @ 1.5A output, 22W maximum Physical Specifications Dimensions 28 x 175 x 119 mm (1.1 x 6.89 x 4.68 in.) Weight 0.3 kg (0.66 lb) Environmental Specifications Operating temperature 0° to 40° C (32. to 104. F) ??? Operating humidity 90% maximum relative humidity, noncondensing ??? Technical Specifications v1.1, May 2008 WNHDE111 5GHz Wireless-N HD Access Point/Bridge User Manual Table A-1. Wireless-N AccessPoint/Bridge Default Configuration Settings Feature Default Setting Electromagnetic Emissions Meets requirements of FCC Part 15 Class B VCCI Class B EN 55 022 (CISPR 22), Class B C-Tick N10947 ??? Interface Specifications LAN 10BASE-T or 100BASE-Tx, RJ-45 Internet 10BASE-T or 100BASE-Tx, RJ-45 Wireless Maximum wireless signal rate complies with the IEEE 802.11 standard. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Radio Data Rates 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps Auto Rate Sensing ??? Frequency ??? Data Encoding 802.11n: ??? 802.11a: ??? Maximum Computers Per Wireless Network Limited by the amount of wireless network traffic generated by each node. Typically 30–70 nodes. Operating Frequency Ranges ? 802.11 Security 40 bit (also called 64 bit) and 128 bit WEP, WPA-PSK and WPA2-PSK. Restoring the Default User Name and Password You can restore the factory default configuration settings to reset the bridge’s user name to admin, the password to password, and the IP address to 192.168.0.100. This procedure erases your current configuration, including your wireless security settings, and restores the factory defaults. When you log in after resetting, the Smart Wizard configuration assistant prompts you to configure these settings. Technical Specifications v1.1, May 2008 WNHDE111 5GHz Wireless-N HD Access Point/Bridge User Manual To restore the factory default configuration settings: 1. Use a sharp object such as a pen or a paper clip to press and hold the restore factory settings button, located on the rear panel of the bridge, for about 20 seconds. 2. Release the restore factory settings button, and wait for the bridge to reboot. The factory default settings are restored so that you can access the bridge from your Web browser using the factory defaults. Technical Specifications v1.1, May 2008 Appendix B Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Document TCP/IP Networking Basics Wireless Networking Basics Preparing Your Network Virtual Private Networking Basics Glossary Link In addition, you can find initial setup instructions for your wireless range extender in the . Related Documents v1.1, May 2008 WNHDE111 5GHz Wireless-N HD Access Point/Bridge User Manual Related Documents v1.1, May 2008 Index A access restricting by MAC address 4-11 access control turning on 4-12 access points 5-3 ActiveX 8-3 adding wireless clients 4-7, 4-10 administrator password, changing 4-12 advanced wireless settings 4-6 attached devices 7-6 autogenerated IP addresses 8-3 automatic logout 3-5 automatic software upgrade 7-9 B backing up configuration file 7-7 basic settings 4-4 bold text xi C cables, checking 8-2 channel, frequency 4-5 channel, wireless port 7-3 clients, adding 4-7, 4-10 communication mode 4-4, 7-3 configuration file backing up 7-7 erasing 7-8 managing 7-7 configuration, erasing A-3, A-4 configuring advanced security 4-6 basic security 4-4 WPA security 4-6 CTS/RTS Threshold 4-7 customer support ii D default factory settings restoring 8-4 deleting configuration 7-8 DHCP server 5-3 Documentation Web page 3-5 documents, reference B-1 Domain Name Server (DNS) addresses current 7-2 E encryption 4-1 encryption keys 4-5 erasing configuration 7-8 Ethernet light, troubleshooting and 8-2, 8-3 Ethernet MAC address 7-7 F factory default settings restoring 8-4 factory settings, restoring A-3, A-4 firmware update 3-5 Firmware Upgrade Assistant 3-4, 7-8 firmware version 7-2 fixed font text xi Index-1 v1.1, May 2008 WNHDE111 5GHz Wireless-N HD Access Po...