Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Fasten the card to the rear of the computer chassis by tightening the screw that is on the PC. 6. Replace the PC cover and reconnect the power cord to the PC. Connect the Network Cables Using the appropriate cable, connect the port on a network hub or switch to the port on the card.The port on the card performs autonegotiation and supports full-duplex operation. This section explains how to install the Network Driver in various Microsoft Windows Operating Systems. Some versions of Microsoft Windows Operating System may respond with different dialog boxes, or the dialog boxes may open in a different sequence than those shown in this guide, but should prompt you for the same information. Before you proceed with the installation steps, decide on a name for your network and for each PC.The whole network must have the same workgroup name while each PC must have a unique name.These names can be entered by going to Start>Settings>Control Panel>Network and clicking on the Identification tab. You also need to have the Microsoft Windows Operating System CD-ROM and the GearBox for Adapters CD ready to use in the installation process. The installation screen uses FA311 as example. Install the Windows XP Network Driver Note: If the “Insert Disk” window opens and a message prompts you to insert your Windows CD-ROM at any time during the installation process, insert the Windows CD-ROM in Drive D (the CD-ROM drive) and click on “OK”.Then follow the next step in the instructions. For FA311 and FA312 Adapters: 1. After installing the FA311 (or FA312) PCI Adapter, the Win XP will install the driver automatically. 2. You can go directly to section 4. “Test Your Network Connection”. Following the steps to check if the driver is well installed. For FA331 Adapters: 1. Turn on the power to the computer and start Windows XP. 2. Double-click “My Computer” on the desktop, double-click “Control panel” and then double-click “System”. 3. Click “Hardware” and click “Device Manager” tab, then double-click “Network adapters”. Installation Guide Everybody’s connecting.™ 32bit 10/100 Mbps Fast Ethernet FA311/FA312/FA331 PCI Adapter SRE TUOR SSELERIW SEHCTIW S SBUH SR ET PAD A ® NETGEAR, Inc. Support Information Phone: 1-888-NETGEAR E-mail: support@NETGEAR.com See Support Information Card for for additional phone numbers. Internet / World Wide Web Go to for the NETGEAR Web page. Defective or damaged merchandise can be returned to your point-of-sale representative. IMPORTANT! Please register online.YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN PROOF OF PURCHASE and this warranty information.To register your product, get product support, or to obtain product information and NETGEAR product documentation, direct your Web browser to the Web page. July 2002 M - F A 3 0 0 N A - 3 Instructions in this guide are for users of Microsoft Windows Operating Systems. As a last step, be sure to register your Adapter at Plan Your Time Estimated setup time for this product is only minutes. Unpack the contents of the package and make sure that you have everything. • FA311 (or FA312, FA331) Fast Ethernet PCI Adapter • GearBox for Adapters CD • FA311/FA312/FA331 Installation Guide Install the Card Note: Touch a grounded metal object to free yourself of static electricity before you handle the card. 1. Turn the power off and unplug the power cord from your computer. 2. Remove the PC cover. 3. Choose an available PCI slot and remove the corresponding back plate from the PC chassis. 4. Insert the card into the PCI expansion slot. Caution: To avoid damaging any components on the card, handle it by the edges, using your thumbs to push it securely into the PCI slot. Make sure the card is fully inserted into the slot to prevent the PC operating system from freezing at startup. 1 VERIFY PACKAGE CONTENTS Model FA311 (or FA312, FA331) Network Card GearBox for Adapters CD 3-pin LAN wake cable (provided with Model FA312) Installation Guide 2 CONNECT NETGEAR TO YOUR ENVIRONMENT Network card Back plate removed PC with network card installed Power adapter PC with network card installed Printer (optional) Hub RJ-45 Connector Category 5 10/100 Mbps UTP cables* RJ-45 Connector Use the cables provided or any Category 5 UTP cable. Maximum length = 100 meters (300 feet) * 4. Double-click “National Semiconductor DP83815-Based PCI Fast Ethernet adapeter”. 5. Click “Driver” and click “Update Driver” tab, then click “OK”. 6. A Hardware Update Wizard will appear. Insert the GearBox for Adapters CD (or disk) into your CD-ROM drive. Select “Install from a list or specific location ( Advanced )”. Click “Next”. 7. When the following dialog box opens, select “Don’t search. I will choose the driver to install.”, then click “Next”. 8. When Select Network Adapter box opens, click “Have Disk” then click “Next”. 1. Open the box and verify its contents 2. Connect NETGEAR to your environment 3. Insta...
Ce manuel est également adapté pour les modèles :Matériel de réseau - FA312 (729.21 kb)