Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink (MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR hub to connect to a PC or the network card, make sure the Normal/Uplink push button is set to Normal. Install the Network Driver This section explains how to install the Windows 98 Network Driver. Some versions of Windows 98 may respond with different dialog boxes, or the dialog boxes may open in a different sequence than those shown in this guide, but should prompt you for the same information. Note: You must install the network card before installing the network driver. Before you proceed with the installation steps, decide on a name for your network and for each PC.The whole network must have the same workgroup name while each PC must have a unique name.These names can be entered by going to Start>Settings>Control Panel>Network and clicking on the Identification tab.You also need to have the Windows 98 CD-ROM and the FA411 Drivers and Diagnostics CD-ROM ready to use in the installation process. Note: If the “Insert Disk” dialog box opens and the “Please insert the disk labeled Windows 98...” message appears at any time during the installation process, insert the Windows 98 CD-ROM in drive D (or whichever letter represents the CD-ROM drive on your notebook computer) and click “OK.”Then follow the next step in the instructions. If you do not have a CD-ROM drive and are using the Windows 98 floppy disks, insert the requested Windows 98 floppy disk in drive A, click “OK,” and then follow the next step in the instructions. 1. If you have chosen to install the card with the PC turned off, turn the power ON now. The new hardware is found, and the driver is automatically loaded. Click “Next.” Select “Search for the best driver for your device (Recommended),” and then click “Next.” 10/100 Mbps PCMCIA Mobile Adapter Installation Guide FA 411 MODEL Introduction NETGEAR’s Model FA411 PCMCIA Mobile Adapter makes it easy to accelerate your notebook PC to Fast Ethernet speeds. It is 16-bit PCMCIA compatible and, with its auto-sensing technology and Ethernet/Fast Ethernet compatibility, ideal for migrating a 16-bit PC card notebook computer from 10 Mbps to 100 Mbps networks. START HERE Instructions in this guide are for users of Windows® 98. As a last step, be sure to register your network card at Plan Your Time Estimated setup time for this product is only minutes. 1. OPEN THE BOX AND VERIFY ITS CONTENTS Make sure that your package contains the following: 2. CONNECT NETGEAR TO YOUR ENVIRONMENT Preparation You will need to have your Windows 98 CD-ROM (or Windows 98 floppy disks) available to complete the installation. Install the Network Card The FA411 PCMCIA Mobile Adapter is hot swappable, which means you can insert it into a PC that is either powered on or shut down. 1. Insert the FA411 PCMCIA Mobile Adapter into the PCMCIA or CardBus slot as illustrated below. Some PCs have two PCMCIA or CardBus slots; the FA411 PCMCIA Mobile Adapter can be inserted into either slot. 2. Insert the RJ-45 adapter cable into the connector on the outer edge of the network card. Model FA411 PCMCIA Mobile Adapter Installation Guide, and Support Information Card Driver and Diagnostics CD-ROM NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Phone: 1-888-NETGEAR E-mail: support@NETGEAR.com Support Information See Support Information Card for phone numbers. Internet / World Wide Web Go to for the NETGEAR Web page. Defective or damaged merchandise can be returned to your point-of-sale representative. IMPORTANT! Please register online.YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN PROOF OF PURCHASE and this warranty information.To register your product, get product support, or to obtain product information and NETGEAR product documentation, direct your Web browser to the Web page. If you do not have access to the World Wide Web, you can register your product using the enclosed registration card and mail it to NETGEAR customer service. February 2001 M 1 - F A 4 1 1 N A - 0 *M1-FA411NA-0* START HERE 1 OPEN BOX AND VERIFY CONTENTS 2 CONNECT NETGEAR TO YOUR ENVIRONMENT Model FA411 PCMCIA Mobile Adapter RJ-45 connectors PC with network card installed Power adapter Notebook PC *Use any Category 5 UTP cable. Maximum length = 100 meters (300 feet) Category 5 10/100 Mbps UTP cables* Model FA411 PCMCIA Mobile Adapter Hub NETGEAR-FA411 This wizard searches for new drivers for: A device driver is a software program that makes a hardware device work. Add New Hardware Wizard < Back Cancel — Next > — What do you want Windows to do? Search for the best driver for your device (Recommended). Display a list of all the drivers in a specific location, so you can select the driver you want. < Back Cancel — Next > — Add New Hardware Wizard 1. Open the box and verify its conten...