Log:
Évaluations - , GPA: ( )

Instructions NETGEAR, Modèle WGT624v4

Fabricant : NETGEAR
Taille : 166.97 kb
Nom Fichier :

Langue d'enseignement: en

Le document est chargé, s'il vous plaît patienter
Le document est chargé, s'il vous plaît patienter


Par ce dispositif a également d'autres instructions :

Facilité d'utilisation


• Your computer may not recognize any DNS server addresses. A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS servers for your use. If you entered a DNS address during the router’s configuration, restart your computer. Alternatively, you can configure your computer manually with DNS addresses, as explained in the documentation for your computer. • Your computer may not have the router configured as its default gateway. Reboot the computer and verify the router address (is listed by your computer as the default gateway address. Restoring the Default Configuration and Password This section explains how to restore the factory default configuration settings, changing the router’s administration password to password and the IP address to You can erase the current configuration and restore factory defaults. To restore the factory default configuration settings, use the Default Reset button on the rear panel of the router. 1. Use a sharp object like a pen or a paper clip to press and hold the default reset button for about 5 seconds (see page 1-3), until the test light on the front blinks. 2. Release the reset button and wait for the router to reboot. Troubleshooting v1.0, April 2007 Router Setup Manual Advanced Troubleshooting Using the Ping Utility Most computers and routers have a diagnostic utility called ping that sends an request to a target device. The device then replies. The ping utility makes it easy to troubleshoot a network. Testing the Path from a PC to Your Router You can ping the router to verify that the LAN path from your computer to your router is set up correctly. 1. From the Windows toolbar, click Start and select Run. 2. In the field provided, type Ping followed by the address of the router, as in this example: ping 3. Click OK. You should see a message like this one: Pinging with 32 bytes of data If the path is working, you see this message: Reply from bytes=32 time=NN ms TTL=xxx If the path is not working, you see this message: Request timed out If the path is not functioning correctly, you could have one of the following problems: • Wrong physical connections — Make sure the LAN port light is on. If the light is off, follow the instructions in “LAN or Internet Port Lights Not On” on page 2-3. — Check that the corresponding lights are on for your computer’s network interface card. • Wrong network configuration — Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your computer. Troubleshooting v1.0, April 2007 Router Setup Manual Testing the Path from a PC to the Internet After verifying that the path between your computer and the router works correctly, test the path from your PC to the Internet. From the Windows run menu, type: PING -n 10 where is the IP address of a remote device such as your ISP’s DNS server. If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies: — Check that your PC has the IP address of your router listed as the default gateway. If the IP configuration of your PC is assigned by DHCP, this information will not be visible in your PC’s Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP default gateway. — Check to see that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device. — If your ISP assigned a host name to your PC, enter that host name as the Account Name in the Basic Settings menu. Troubleshooting v1.0, April 2007 Appendix A Technical Specifications This appendix provides technical specifications for the router. Network Protocol and Standards Compatibility Data and Routing Protocols: TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond, Dynamic DNS, and UPnP Power Adapter North America: 120V, 60 Hz, input UK, Australia: 240V, 50 Hz, input Europe: 230V, 50 Hz, input Japan: 100V, 50/60 Hz, input All regions (output): 12 V DC @ 1.0A output Physical Dimensions: 1.1" x 5.8" x 3.8" 286 x 147 x 957 mm Weight: 0.57 lbs. 0.26 kg Environmental Operating temperature: 0° to 40° C (32. to 104. F) Operating humidity: 90% maximum relative humidity, noncondensing Electromagnetic Emissions Meets requirements of: FCC Part 15; EN 301489; EN 60950 (CE LVD) Interface Specifications LAN: 10BASE-T or 100BASE-Tx, RJ-45 WAN: 10BASE-T or 100BASE-Tx, RJ-45 Technical Specifications v1.0, April 2007 Router Setup Manual Technical Specifications v1.0, April 2007 Appendix B Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Document Internet Networking and TCP/IP Addressing Preparing a...

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories