Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
When ON, this feature has two modes of operation as follows: 1 Automatic 2 Manual 48 LINESHARE PRO To turn Emergency Call Override ON (automatic mode), enter the programming mode and press the following on your tone phone: 5 Emergency Call Override 1 Automatic * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming [6] Dual Tone Assignments The Dual Tone Assignments function allows you to define the port access code to each of the Lineshare Pro ports. When you or a caller enter this code on the keypad of a tone phone, the Lineshare Pro transfers the call to the selected port. You can enter up to a four-digit code in this position for each of the ports. The Dual Tone Assignments are factory-preset as follows: • Port 1 1 1 • Port 2 2 2 • Port 3 3 3 • Port 4 4 4 NOTE You can set only one port’s assignment per programming sequence. To select a new Dual Tone Assignment for a port, press the following on your tone phone: 6 Dual Tone Assignments The desired port selection (1-4) The desired new access code * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming NOTE Do not program similar, or identical access codes into PORT 1, PORT 2, PORT 3, or PORT 4 Dual Tone Assignments (example: PORT 1 = 123, PORT 2 = 1234). Similar or identical codes may interfere with proper operation. 49 LINESHARE PRO [7][5] Time at Home The Time at Home function controls the amount of time that the Lineshare Pro holds the phone line open and listens for a routing command. It is activated when the Lineshare Pro is in the secured mode, or when Home Routing is turned ON and a call is routed home. When the Time at Home period expires, the Lineshare Pro disconnects the call without rerouting to another port. NOTE You must turn ON the Home Routing feature in order for this function to activate, even in the secured mode. The Time at Home is factory- preset, 3 0 *, which allows 30 seconds for a routing command to be entered. The range of this function can be set between 1 to 60 seconds. To change the Time at Home to 40 seconds, enter the programming mode and press the following on your tone phone: 7 5 Time at Home 4 0 Set time to 40 seconds * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming [7][6] Extension Detection Timer The Extension Detection Timer operates only when the Lineshare Pro is configured in the non-secured mode. This function controls the amount of time that the Lineshare Pro allows an extension phone (not connected to one its ports) to answer an incoming call that is ringing the primary default port. The Extension Detection Timer is factory preset, 1 5 *, which allows 15 seconds for a routing command to be entered. The timer can be set for from 1 to 30 seconds. To change the Extension Detection Timer to 25 seconds, enter the programming mode and press the following on your tone phone: 7 6 Extension Detection Timer 2 5 Set time to 25 seconds * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming [8] Rings Available to the Ports The Rings Available to the Ports feature allows you to define the number of rings available to each port. The number of rings available to the ports range from 0 to 99 rings. The Rings Available to the Ports are factory-preset as follows: 50 LINESHARE PRO • Port 1 6 rings • Port 2 4 rings • Port 3 4 rings • Port 4 4 rings To change the Rings Available to a port to 20 rings, enter the programming mode and press the following on your tone phone: 8 Rings Available to the FAX/MODEM Port The selected port 2 0 The desired new number of rings * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming [8] [5] Rings to Answer Call The Rings to Answer Call feature determines the number of rings received for a incoming phone call before the Lineshare Pro answers. The factory setting is one ring, to permit the Lineshare Pro to answer and transfer calls as quickly as possible. Under normal circumstances, it is not necessary to change this setting. However, if you have the phone company’s “Caller ID” service, you must set the Rings to Answer Call to two rings. This function has a range of 0 to 99 rings to answer a call. The Rings to Answer Call is factory-preset to one ring, 8 5 1 *. To change the Rings to Answer Call to two rings, enter the programming mode and press the following on your tone phone: 8 5 Rings to Answer Call 2 The desired new number of rings * End programming sequence (3 beeps indicate correct entry) (Optional entries for additional changes) * Save changes and exit programming [9] [9] [9] Reset to Factory Settings To reset all features to their original factory settings, enter the programming mode a...