Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
Local Cable Network Service Before installing the cable modem, contact your local cable check the availability of Internet/Cable network access. Read Guide thoroughly before attempting to install the cable modem. Check Your Package Contents These are the items included with your DCM-202 purchase: D-Link Cable Modem DCM-202 CD-ROM (containing USB Drivers, Manual, and Warranty) Ethernet (CAT5 UTP/Straight-Through) Cable USB Cable 12V DC, 1A Power Adapter Device Stand If any of the above items are missing, please contact your reseller. ©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. DCM-202. 02132004 Requirements RF coaxial cable: • One section of coaxial cable • Three sections of coaxial cable if • A cable line-splitter, if you wish to connect the cable modem same wall cable outlet (optional). • An active two-way cable line installed by your local cable operator. .. Modem Make and Model i.e. D-Link DCM-202 .. Modem Serial Number i.e. 202102XXXXXXX (normally found on the label on the bottom of the modem) .. Modem MAC (CMAC) Address i.e. 0050BAXXXXXX (found on the rear of the modem) Please contact your local cable company and service and register this cable modem on provider will need the following modem information: Computer System Requirements: • Pentium processor equivalent (Pentium 166MHz or higher recommended). • The original Windows Operating System CD-ROM or diskettes. • TCP/IP protocol installed (see the “Configuring the TCP/IP Protocol on Your PC” section for more information about TCP/IP installation). • An active Ethernet port or network interface card (NIC) installed in your computer. The cable modem is OS-independent and can be connected to any computer equipped with an active standard RJ-45 10Base-T Ethernet port. For USB connectivity: • A computer must have Windows XP, 2000, Me or 98SE operating system. • An active USB port on your computer. For Ethernet connectivity: • A PC running Windows, Macintosh, or Linux operating system. • An active Ethernet adapter installed in your computer such as the DFE-530TX+. The DCM-202 USB/Ethernet Cable Modem will work only with the Ethernet port and/or the USB port connected. 2 USB Installation The USB connection Microsoft Windows XP, 2000, Me or 98SE Connect the Cables and Power Adapter To use the computer’s USB interface to connect to the Internet, use the provided USB cable to connect the computer and the cable modem. A. Power off the computer. B. Unplug the computer’s power cable. C. Connect the RF coaxial cable (not included) to the back of the cable modem labeled “CATV”; connect the other end to the wall cable outlet. Note: If you are using a cable line-splitter (not included) to connect the computer and a television to the same wall cable outlet, you will use three separate coaxial cables. As shown in the Ethernet NIC illustration (see above), a cable line-splitter has three connectors. Use the illustration to make the appropriate coaxial cable connections. D. Plug the USB cable into the cable modem’s USB port and the other end of the cable to the computer’s USB port. E. Connect the 12VDC/1A power adapter to the back of the cable modem labeled “Power.” Be sure to use only the 12VDC/1A power adapter that came with the cable modem. Using the wrong power adapter can damage the cable modem and void the warranty. F. Plug the power adapter into a surge protector or an electrical outlet. G. Power on the computer. Within a few minutes, the computer detects the cable modem. 3 USB Installation Insert the DCM-202 CD-DCM-202 welcome screen Close to return to the cable modem installation process. Leave Windows can access the software driver files required for the Windows XP: The Found New Hardware Wizard screen appears. Click Next Select Install the software automatically (Recommended). 4 USB Installation Click Finish to finalize the installation. You can now go to “ Check the LEDs. ” Windows 2000: The Found New Hardware Wizard screen appears. 1 Insert the D-Link Installation and Documentation CD into the computer’s CD-ROM drive. a Shut down the computer. b Connect the USB cable between the DCM-202 and an available USB Port on the computer. 2 Power on the computer. After the computer boots up: a Windows detects the cable modem. b The Found New Hardware screen appears. c The Found New Hardware Wizard screen appears. 3 Select Search for a suitable driver for my device (recommended) and click Next. 4 Check the CD-ROM Drives check box and click Next to search for the necessary driver files. 5 When the correct location of the driver file appears, click OK. 6 The Found New Hardware Wizard displays the search results. 7 Click Next to install the driver files for the cable modem. 8 Click Finish to continue. Windows Me: The Add New Hardware Wizard screen appears. A. Select Automatically search for a better driver (Recommended) and cli...