Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
• Replace a cracked or suspect wheel. • Always allow a new wheel to run for a few minutes at full speed before using it. Stand to one side at start up. • Check that the wheel rotates freely each time before start up. • Do not use the grinder unless all the guards are properly fitted and secure. • Check that the tool rests are properly adjusted before commencing use. • Do not overload the grinder. Allow the grinder to run at full speed, or close to full speed during use. • Never apply excessive pressure to the wheel. It might shatter causing personal injury. • Make sure that the wheel is not in contact with the work when you start the grinder. • When using the grinder, use safety equipment including safety goggles or shield, ear protection, dust mask and protective clothing including safety gloves. Wear safety goggles Wear ear protection Wear a breathing mask 5 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Assembly The BGSTAND needs to be assembled prior to use, assembly will take approximately 20 minutes. Required Tools The following tools are required: • 5mm hex key (supplied) • 8mm hex key (supplied) • Phillips head screwdriver (not supplied) • Wrench (not supplied) Components The BGSTAND is supplied with the following components: 1. Base 2. Fixed support pole 3. Adjustable support pole 4. Accessory storage compartment 5. Wheel storage compartments 6. Bench grinder support plate 7. Pan head tapping screws (x4) 8. Tension handle 9. Hook, pan head screw and flat washer 10. 8mm and 5mm hex keys 11. M10 x 50mm bolts with flat washers, spring washers and nuts (x4) 12. M6 x 40mm bolts with flat washers, spring washers and nuts (x4) 5104938 12712611 7 Know your product Before using the tool, familiarize yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. Base 2. Fixed support pole 3. Adjustable support pole 4. Accessory storage compartment 5. Wheel storage compartment (x2) 6. Bench grinder support plate 7. Pan head tapping screws (x4) 8. Tension handle 9. Hook 10. 8mm and 5mm hex keys 7 10 8 1 2 4 3 6 9 5 8 Assembly 1. Place the fixed support pole into the base. 2. Secure the fixed support pole to the base by tightening the 2 recessed hex screws in the base, use the 5mm hex key to tighten these screws. 3. Place the adjustable support pole into the fixed support pole. 4. Position the adjustable support pole so that the slot in the pole is in line with the Phillips head screw. 5. Using a Phillips head screwdriver tighten the screw so that it extends into the recess. 6. Lower the adjustable support pole and let it rest on the Phillips head screw for support. 7. Attach the tension handle to the front of the fixed support pole and tighten, this will hold the adjustable support pole in position. 8. Fit the accessory storage compartment over the adjustable support pole and lower down onto the fixed support pole. 9. With the accessory storage compartment positioned at the top of the fixed support pole tighten the 2 hex bolts to secure the compartment in position. 10. Fit the wheel storage compartments onto the accessory storage compartment and using a Phillips head screwdriver tighten the 4 pan head tapping screws to secure the wheel storage compartments in place. 11. Fit the bench grinder support plate onto the top of the adjustable support pole. 12. Secure the bench grinder support plate in position by tightening the 2 recessed hex screws located underneath the plate. 9 13. Position the hook on the front of the bench grinder support plate and secure using the pan head screw and flat washer. WARNING! DO NOT fit the bench grinder to the stand until the stand is bolted through or into the floor. This stand is not designed to be a free standing stand, and the base must be secured to the floor or area where the stand will be positioned. Do not fit the grinder or operate the grinder without the base being firmly attached as it will tip over. Adjusting the height WARNING. Always ensure that the bench grinder is removed from the bench grinder support plate before adjusting the height. 1. Loosen the tension handle. 2. Whilst holding the bench grinder support plate rotate the support plate in a clockwise direction to disengage the height location. 3. Raise or lower the support plate to the desired height. 4. Rotate into the nearest height location by rotating the support plate in an anti-clockwise direction. 5. Tighten the tension handle to secure the pole and support plate in position. IMPORTANT. It is important to ensure the adjustable stand is correctly located into one of the pre set height positions. Do not attempt to use the stand if it i...
Ce manuel est également adapté pour les modèles :Les machines à rectifier - NTS2000A (881.67 kb)