Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
SAVE THESE INSTRUCTIONS Work Area or "W." These cords are rated for outdoor use Keep your work area clean and well lit. and reduce the risk of electric shock. Refer to Cluttered benches and dark areas invite “Recommended sizes of Extension Cords” in accidents. the Accessory section of this manual. Do not operate power tools in explosive Personal Safety atmospheres, such as in the presence of Stay alert, watch what you are doing and flammable liquids, gases, or dust. Power use common sense when operating a tools create sparks which may ignite the dust power tool. Do not use tool while tired or or fumes. under the influence of drugs, alcohol, or Keep by-standers, children, and visitors medication. A moment of inattention while away while operating a power tool. operating power tools may result in serious Distractions can cause you to lose control. personal injury. Electrical Safety Dress properly. Do not wear loose clothing Double Insulated tools are equipped with a or jewelry. Contain long hair. Keep your polarized plug (one blade is wider than the hair, clothing, and gloves away from other.) This plug will fit in a polarized outlet moving parts. Loose clothes, jewelry, or long only one way. If the plug does not fit fully in hair can be caught in moving parts. Keep the outlet, reverse the plug. If it still does handles dry, clean and free from oil and not fit, contact a qualified electrician to grease. install a polarized outlet. Do not change the Avoid accidental starting. Be sure switch is plug in any way. Double Insulation “OFF” before plugging in. Carrying tools eliminates the need for the three wire with your finger on the switch or plugging in grounded power cord and grounded power tools that have the switch “ON” invites supply system. Before plugging in the tool, be accidents. certain the outlet voltage supplied is within the Remove adjusting keys or wrenches before voltage marked on the nameplate. Do not use turning the tool “ON”. A wrench or a key “AC only” rated tools with a DC power supply. that is left attached to a rotating part of the Avoid body contact with grounded surfaces tool may result in personal injury. such as pipes, radiators, ranges and Do not overreach. Keep proper footing and refrigerators. There is an increased risk of balance at all times. Proper footing and electric shock if your body is grounded. If balance enables better control of the tool in operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter unexpected situations. must be used to supply the power to your Use safety equipment. Always wear eyetool. Electrician’s rubber gloves and footwear protection. Dust mask, non-skid safetywill further enhance your personal safety. shoes, hard hat, or hearing protection must be Don't expose power tools to rain or wet used for appropriate conditions. conditions. Water entering a power tool will Tool Use and Care increase the risk of electric shock. Use clamps or other practical way to Do not abuse the cord. Never use the cord secure and support the workpiece to a to carry the tools or pull the plug from an stable platform. Holding the work by hand or outlet. Keep cord away from heat, oil, sharp against your body is unstable and may lead to edges or moving parts. Replace damaged loss of control. cords immediately. Damaged cords increase the risk of electric shock. Do not force tool. Use the correct tool for your application. The correct tool will do the When operating a power tool outside, use job better and safer at the rate for which it is an outdoor extension cord marked "W-A" designed. -2 Do not use tool if switch does not turn it caused by poorly maintained tools. Develop a “ON” or “OFF”. Any tool that cannot be periodic maintenance schedule for your tool. controlled with the switch is dangerous and Use only accessories that are must be repaired. recommended by the manufacturer for Disconnect the plug from the power source your model. Accessories that may be suitable before making any adjustments, changing for one tool, may become hazardous when accessories, or storing the tool. Such used on another tool. preventive safety measures reduce the risk of starting the tool accidentally. Service Tool service must be performed only by Store idle tools out of reach of children and qualified repair personnel. Service or other untrained persons. Tools are maintenance performed by unqualified dangerous in the hands of untrained users. personnel could result in a risk of injury. For Maintain tools with care. Keep cutting tools example: internal wires may be misplaced or sharp and clean. Properly maintained tools, pinched, safety guard return springs may be with sharp cutting edges are less likely to bind improperly mounted. and are easier to control. Any alteration or When servicing a tool, use only identical modification is a misuse and may result in a replacement parts. Follow instructions in dangerous condition. the Maintenance section of this manual. Ch...