Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
Do not start the tool on the workpiece. Always run the tool for at least one minute before operation. This allows the tool to reach full speed. ! CAUTION RELEASE TABS VARIABLE SPEED DIAL (Model 1295DVS only) BM 2610914126 9-03 10/1/03 10:31 AM Page 6 BM 2610914126 9-03 10/1/03 10:31 AM Page 7 Operating Instructions ROCKER “ON/OFF” SWITCH (Models 1295D, 1295DP, & 1295DVS) TO TURN THE TOOL "ON" depress the upper portion of the dust-protected switch to the number “1” position. TO TURN THE TOOL "OFF": depress the lower portion of the switch to the number “0” position. THREE-POSITION ROCKER SWITCH WITH SWIFTSAND™ SETTING (Model 1295DH only) Your tool is equipped with a three-position switch which allows normal surface finishing or faster stock removal with the SwiftSand™ option. TO TURN THE TOOL "ON" for normal finishing, depress the lower portion of the dust-protected switch to the number (1) position. TO THE TURN THE TOOL "ON" in the SwiftSand™ (high removal) setting, depress the upper portion of the switch to the number (2) position. TO TURN THE TOOL "OFF" from either setting move the switch to the center number “0” position. Setting Applications 1 Normal surface finishing for wood, plastics, solid-surfacing and composites. 2 SwiftSand™ setting for solid wood, fast stock removal, paint removal, fast blending of joints or repairs in solid surfacing. Metal sanding and finishing, chipboard, course sanding of wood and other surfaces. Finish removal, light polishing or scratch blending. VARIABLE SPEED WITH DIAL SETTING (Model 1295DVS only) Your sander is also equipped with a variable speed dial. The sander's orbital pad speed can be preset from minimum to maximum nameplate OPM by rotating the dial in the housing. The dial may be set on or between any of six positions (1=low through 6=high). The following table may be used as a general guide for abrasive and backing pad selection, but the best results will be obtained by sanding a test sample of the workpiece first. Switch Backing Grit Material setting pad size rough/finish rough/finish woods: softwoods 4 / 6 soft 60 / 240 hardwoods 4 / 6 med 60 / 180 veneers 4 soft 240 / 320 metals: steel 4 med 60 / 240 stainless 4 med 120 / 240 aluminum 4/ 6 med 80 / 240 rust spots 6 soft 60 / 120 paintwork: sanding 2 / 3 med 180 / 400 scratches 4 / 6 hard 120 / 240 stripping 4 med 40/60 /80 BACKING PAD INSTALLATION To change backing pad, hold pad firmly and The random orbit sander is equipped with a turn screw counterclockwise with 5mm allen backing pad of medium hardness, which is wrench provided. Remove old pad, and place suitable for general service. Harder and softer new pad over locating pins on drive spindle. pads are available for other purposes, and in Replace screw and securely tighten in a general are used as follows; clockwise direction with the allen wrench. Damaged or worn backing pads must be Soft pad - Polishing or sanding large or curved replaced immediately. surfaces. BACKING PAD DAMPER Medium pad - All purpose general sanding and polishing. Your tool is equipped with an integrated backing pad damper ring. This damper Hard pad - Heavy sanding on flat surfaces, reduces the no-load speed, which helps especially with coarser abrasives. prevent accidental marking of the workpiece surface and provides uniform finishing. -7 BM 2610914126 9-03 10/1/03 10:31 AM Page 8 NOTE: If you notice steadily increasing no- load speed, this indicates that the damper ring is worn and needs to be replaced. To replace damper ring, remove backing pad as described in “Backing Pad Installation” and remove worn damper ring by pulling firmly out of locating groove. Loosen the two screws on shroud just enough so you can separate shroud approximately 1/4 inch. Align locating bumps on damper ring with cut outs in shroud and depress ring with thumbs until shroud seats into groove completely around ring, then tighten screws. IMPORTANT: Ring should not have bends or ripples when correctly seated. Apply a thin film of light grease to top side of backing pad where the damper ring makes contact, reassemble backing pad and firmly tighten screw. BACKING PAD DAMPER RING SHROUD LOCATING BUMPS ON UNDERSIDE OF DAMPER RING INSTALLING ACCESSORIES (Model 1295D 1295DH & 1295DVS) DUST COLLECTION CANISTER Your random orbit sander uses hook-and-loop The integral dust extraction system collects backed accessories, which firmly grip the pad sanding dust in canister supplied with your when applied with moderate pressure. To sander. For maximum efficiency, the dust change the accessory, merely peel off the old canister should be emptied frequently during accessory, remove dust from the pad if operation. necessary, and press the new accessory in When the canister is removed from the tool an place. Be sure to align the sanding disc holes (optional vacuum hose accessory) can be with the holes in the backing pad to allow the attached to the dust port. dust extraction system to function. To use this feature, attach vacuu...
Ce manuel est également adapté pour les modèles :Les machines à rectifier - 1295DP (449.16 kb)
Les machines à rectifier - 1295DVS (449.16 kb)