Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. NOTICE Safety Instructions 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of check- ing to see that keys and adjusting wrenches are removed from winch before operation. 3. KEEP CHILDREN AWAY. All chil- dren should be kept at a safe dis- tance from winch. 4. DO NOT USE UNDER THE INFLU- ENCE OF DRUGS OR ALCOHOL. 5. NEVER ALLOW UNTRAINED USERS TO RUN THIS TOOL WHILE UNSUPERVISED. 6. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. 7. ALWAYS USE SAFETY GLASS- ES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resis- tant lenses, they are NOT safety glasses. 8. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING THE TOOL. H3117 Mini Grinder -1 Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD 14. MAINTAIN TOOLS WITH CARE. for the tool. Make sure your exten-Keep tools sharp and clean for sion cord is in good condition. best and safest performance. Conductor size should be in accor-Follow instructions for lubricating dance with the chart below. The and changing accessories. amperage rating should be listed on 15. DISCONNECT TOOLS before serthe motor or tool nameplate. An vicing and changing accessories, undersized cord will cause a drop in such as blades, bits, cutters, and line voltage resulting in loss of power the like. and overheating. Your extension 16. REDUCE THE RISK OF UNIN- cord must also contain a ground wire TENTIONAL STARTING. Make and plug pin. Always repair or sure switch is in off position before replace extension cords if they plugging in. become damaged. 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s Minimum Gauge for Extension Cords manual for recommended acces- AMP LENGTH RATING 25ft 50ft 100ft 0-6 18 16 16 7-10 18 16 14 11-12 16 16 14 13-16 14 12 12 17-20 12 12 10 21-30 10 10 No sories. The use of improper accessories may cause risk of injury. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended 10. WEAR PROPER APPAREL. Do not function. Check for alignment of wear loose clothing, gloves, neck- moving parts, binding of moving ties, rings, bracelets, or other jewel- parts, breakage of parts, mount ry which may get caught in moving ing, and any other conditions that parts. Non-slip footwear is recom may affect its operation. A guard or mended. Wear protective hair cover- other part that is damaged should ing to contain long hair. be properly repaired or replaced. 11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eye glasses only have impact resistant lenses, they are NOT safety glasses. 12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool. 13. DON’T OVERREACH. Keep proper footing and balance at all times. No list of safety guidelines can be complete. Operating this tool may require additional safety precautions specific to your working environment. Failure to use reasonable caution while operating this tool could result in serious personal injury. -2- H3117 Mini Grinder H3117 Mini Grinder -3- INTRODUCTION The specifications, details, and photographs in this manual represent the Model H3117 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: Commentary We are proud to offer the Grizzly Model H3117 Mini Grinder. This model is part of a growing Grizzly family of fine tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The Model H3117 features a 1.8" collet, a collet lock, a collet wrench, removable electric motor brushes, a variable speed dial, and a wide assortment of bits. We are pleased to provide this manual with the Model H3117. It was written to encourage safety considerations and guid...