Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
33 for use with a dust collection system. You must adjust the shield to suit your sanding operation. 1. If you are sanding with the disc, push in on the dust shield (A) Fig. 33. A Fig. 33 14 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. A Fig. 34 WRENCH STORAGE A hole is provided in the stand for storing the hex wrench (A) Fig. 35, supplied with the sander. REMOVING UPPER SANDING A Fig. 35 DRUM GUARD You can remove the upper sanding drum guard (A) Fig. 36 to sand inside curved work or to change the belt. To remove: 1. Pull outward on the guard (A). 2. After the sanding operation is completed or the belt is changed, replace the guard (A) Fig. 36 on the two studs (B), one of which is shown. A B Fig. 36 REPLACING SANDING BELT DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the upper sanding drum guard. Loosen the two screws (A) Fig. 37 and remove the backstop (B). 2. Loosen the two screws (C) Fig. 37, and remove support bracket (D). Fig. 38 illustrates backstop and support bracket removed from the machine. B A D C Fig. 37 Fig. 38 15 4. Move the tension lever (E) Fig. 39, to the right to the “LOOSEN” position (F). Remove the sanding belt (F) from both sanding drums. 5. Place a new 6" x 48" sanding belt (F) Fig. 40 over both sanding drums (G). Ensure that the belt will travel in the direction of the arrows printed on the inside of the belt. 6. Move the tension lever (E) Fig. 39 left to the “TIGHTEN” position. 7. Replace the support bracket, backstop and upper sanding drum guard, removed in STEPS 1 and 2. 8. Connect the electrical power to the sander. If the belt is not tracking properly, refer to section “TRACKING THE SANDING BELT.” REPLACING SANDING DISC DISCONNECT MACHINE FROM POWER SOURCE. 1. Loosen the screw (A) Fig. 41, and remove the table assembly (B). 2. Remove the three screws (C) Fig. 42 and lower the cover (D). 3. Peel off the old disc (E) Fig. 43. 4. Make sure the disc plate (F) Fig. 43 is clean. Peel the backing from a new sanding disc. Press the new sanding disc firmly into position on the disc plate (F). Replace the lower cover and table assembly, removed in STEPS 1 and 2. F E Fig. 39 G G F Fig. 40 A B Fig. 41 C D E F Fig. 42 Fig. 43 16 OPERATING CONTROLS AND ADJUSTMENTS A A Fig. 44 Fig. 45 SURFACING OR EDGE SANDING WITH SANDING BELT When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the backstop (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt. Place the end of the workpiece against the backstop and move the workpiece evenly across the sanding belt. Apply only enough pressure to allow the sanding belt to remove material. Use extra caution when sanding very thin pieces. Position the edge of the backstop a maximum of 1/16" away from the sanding belt to avoid trapping the workpiece or your fingers between the backstop and the sanding belt. SANDING INSIDE CURVES You can sand inside curves on the top sanding drum (Fig. 46). Replace the sanding drum guard after the sanding operation is completed. SANDING OUTSIDE CURVES Sand outside curves on the sanding disc as illustrated in Fig. 47. Always sand on the left (downward) side of the sanding disc. Sanding on the right (upward) side of the sanding disc could cause the workpiece to fly up, which could be hazardous. The edge of the table must be positioned a maximum of 1/16" away from the sanding disc to avoid trapping the workpiece or fingers between the table and sanding disc. Fig. 46 Fig. 47 17 Fig. 48 Fig. 49 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and the accessory miter gauge (Fig. 48). Move the work from the center to the left side of the sanding disc. Always sand on the left (downward) side of the sanding disc. Sanding on the right (upward) side of the sanding disc could cause the workpiece to fly up, which could be hazardous. The edge of the table must be positioned a maximum of 1/16" away from the sanding disc to avoid trapping the work or fingers between the table and the sanding disc. END SANDING WIDE WORKPIECES WITH THE BELT When sanding the ends of wide workpieces, move the table assembly to the the sanding belt and use the sanding arm in the vertical position (Fig. 49). See sections titled “CHANGING POSITION OF SANDING ARM” and“USING TABLE ASSEMBLY WITH SANDING BELT.” For more accurate work use the accessory miter gauge and move the work evenly across the sanding belt (Fig. 52). Always sand on the left (downward) side of the sanding disc. Sanding on the right (upward) side of the sanding disc could cause the workpiece to fly up, which could be hazardous. 18 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI ...