Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
English English 4-1/2" Cutting Wheels Sanding Discs 4-1/2" Sanding Flap Discs Type 1 guard backing flange abrasive cutting wheel clamp nut Type 1 guard backing flange diamond cutting wheel clamp nut rubber backing pad sanding disc threaded clamp nut hubbed sanding flap disc backing flange non-hubbed sanding flap disc threaded clamp nut Type 27 guard Type 27 guard 1. Open the guard latch (M). Align N the lugs (N) on the guard with the slots (O) on the gear case. 2. Push the guard down until the guard lugs engage and rotate freely in the groove on the gear O case hub. 3. With the guard latch open, rotate the guard (I) into the desired working po sition. The guard body should be positioned between the spindle and the operator to provide maximum operator protection. M I 4. Close the guard latch to secure the guard on the gear case. You should not be able to rotate the guard by hand when the latch is closed. Do not operate the grinder with a loose guard or the clamp lever in open position. 5. To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard. NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory. If, after a period of time, the guard becomes P loose, tighten the adjusting screw (P) with clamp lever in the closed position. 7 CAUTION: Do not tighten the adjusting screw with the clamp lever in open position. Undetectable damage to the guard or the mounting hub may result. CAUTION: If guard cannot be tightened by adjusting clamp, do not use tool and take the tool and guard to a service center to repair or replace the guard. MOUNTING AND REMOVING GUARD O (D28110) N 1. Loosen screw. Align the lugs (N) on the guard with slots (O) on the gear case. 2. Push the guard down until the guard lug engages and rotates freely in the groove on the gear case hub. 3. Rotate guard (I) into desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection. 4. Tighten the screw to secure the guard on the gear case cover. You should be unable to rotate the guard by hand. Do not operate grinder with a loose guard. 5. To remove the guard, loosen screw, rotate the guard so that the arrows are aligned and pull up on the guard. OPERATION Guards and Flanges It is important to choose the correct guards and flanges to use with the grinder accessories. See page 6 and this page for the correct accessories. NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose. WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If 8 it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 6–7. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate. Switches CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down. NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down. PADDLE SWITCH (D28402, D28402N) CAUTION: Before connecting the tool to a power source depress and release the paddle switch (A) once [D28402: without depressing the lock-on button (J)] to ensure that the switch is off. Depress and release the paddle switch as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the paddle switch is locked on, thelock-off lever (B) toward the back of turn the tool on, push the tool will start unexpectedly when it is reconnected. A B Tothe tool, then depress the paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch. WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is laid down. English English SLIDER SWITCH (D28110, D28112) CAUTION: Before connecting the tool to a power supply, be sure the switch is in the off position by pressing the rear part of the switch and releasing. Ensure the switch is in the off position as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the switch is locked on when the power is connected, the tool will ...
Ce manuel est également adapté pour les modèles :Les machines à rectifier - D28402N (2.45 mb)