Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
IO. Use the specified surface of the wheel to perform the grinding. 11. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 12.Do not leave the tool running. Operate the tool only when hand-held. 13.Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. Installing side grip (auxiliary handle) 5 Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Screw the inner flange onto the spindle. Hold the spindle with the wrench so that Lock nut it cannot revolve, then use the lock nut I wrench to secure the inner flange. Fit the Depressed center wheel wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 5 Switch action Slide the slide switch forward to start, and Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the work- piece. In general, keep the edge of the wheel or disc at an angle of about 15" to the work- piece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions. WARNING : 0 It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. .Continued use of a worn-out wheel may result in wheel explosion and serious personal injury. Depressed center wheel should not be used after it has been worn down to 75 mm (3") in diameter. Use of the wheel after this point is unsafe and it should be removed from service and rendered unusable by intentional destruction. Overload protector The overload protector automatically cuts out to break the circuit and the button pops out, whenever heavy work is pro- longed. Wait 20-30 seconds before press- ing the restart button to resume operation. The tool should be switched off when you press the restart button, however. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELl AB1 LITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @ Wheelcover Part No. 342554-4 @ Depressed center wheels 99 Part No. Size lmm) Grit 100x4~16 @ Rubberpad (For abrasive disc) Part No. 743009-6 Wheels Der Dka 0 Inner flange 35 (For depressed center wheel) Part No. 224291-1 @I Lock nut 10-35 (For depressed center wheel) Part No. 224545-6 @ Abrasivedisc (10 pcs. per pkg) 24 794066-7 r) 794065-9 794227-9 100 I 794069-1 120 0Sanding lock nut 30 @ Wire cup brush 75 (For abrasive disc) Part No.7432014 Part No. 224501-6 @ Grip holder Wire bevel brush 85 Part No. 164329-9 Part No. 191784-2 0 Grip 26 0 Wrench 14 Part No. 273485-5 Part No. 781007-2 0 Lock nut wrench 20 Part No. 782401-1 Fsb-06-'92 US lKDl 100 mm (4") DISC GRINDER Model 9514B Note: The switch and other part configurations may differ from country to country. MODEL 95140 Feb.-06-'92 US lKD1 'i\M DESCRIPTION DESCRIPTION AtD A:D ~~ MACHINE 1 1 Spiral Bevel Gear 11 17 1 Switch Lever 21 1 Ball Bearing 600OLB 22 1 Woodruff Key 3 Fan 60 23 1 Needle Bearing 810 ARMATURE ASSEMBLY 24 1 0 Ring 11 (With Item 2 -51 25 1 Retaining Ring S-12 5 1 Ball Bearing 627LLB 26 1 Spiral Bevel Gear 36 61 FIELD ASSEMBLY 27 1 Ball Bearing 6201LB 72 Carbon Brush 28 1 Flat Washer 12 8 1 Terminal Base 29 1 Spindle 9 6 Tapping Screw BT 4x25 30 1 Wheel Cover 10 1 Housing Set lWith Item 121 31 2 Pan Head Screw M5x20 (With Washer1 11 1 Name Plats Inner Flange 35 12 1 Housing Set (With Item 101 Lock Nut 10-35 13 1 Switch Over Current Relsy 14 1 Cord Grip Holder 16 1 Comoressian Swim 6 Grip 26 Note: The switch and other part spwifications may differ from country to country. MAKCTA LIMrEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects...