Log:
Évaluations - , GPA: ( )

Instructions Makita, Modèle 9741

Fabricant : Makita
Taille : 604 kb
Nom Fichier : c95f733b-77bf-9184-3d2d-df7f155297c9.pdf

Langue d'enseignement: en

Le document est chargé, s'il vous plaît patienter
Le document est chargé, s'il vous plaît patienter

Facilité d'utilisation


2. Do not wear gloves during operation. 3.Hold the tool firmly with both hands. 4. Keep hands away from rotating parts. 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Never attempt to use with the tool held upside down in a vise, etc. SAVE THESE INSTRUCTIONS. Removing or installing wheel CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the wheel. To remove the wheel, insert one hex wrench into the end of the spindle and another hex wrench into the end of the output shaft. Turn the hex wrench in the output shaft clockwise while securely hold- ing the hex wrench in the spindle so that the wheel cannot revolve. Pull the output shaft out from the wheel. Move the wheel slightly away from the spindle and remove the wheel from the tool. CAUTION: The output shaft has a left hand thread. To install the wheel, follow the removal procedures in reverse. When installing it, be sure to align the notches in the wheel with the pins on the spindle. Adjusting front roller The front roller allows you to apply uni- form pressure to the workpiece. To adjust the front roller, set the tool on a flat sur- face and loosen the wing nut. Adjust the front roller up or down until the clearance distance (D) is about 2 mm (5/64”).Tighten the wing nut securely. \ Front roller Connecting to dust collector (Optional accessory) The use of a dust collector makes sanding operations clean and dust collection easy. To connect a dust collector, open the dust port by sliding the cover plate up and in a clockwise direction. Attach the joint onto the dust port. Now a dust collector can be connected to this tool. CAUTION: When not using a dust collector, close the dust port opening with the cover plate. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous Trigger switch . operation, pull the trigger and then push in I the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. . CAUTION: Before plugging in the tool, always check to see that the trigger swith actuates properly and returns to the "OFF" position when released. 6 Operation Hold the tool firmly with both hands on the handle and the grip in front. Place the tool on the workpiece surface and move the tool gently forward and backward while applying slight downward pressure. CAUTION : *The tool should not be in contact with the workpiece surface when you turn the tool on or off. Damage to the tool or the workpiece surface and injury to the operator may resuIt. Apply slight downward pressure only. Excessive pressure may decrease tool efficiency, shorten wheel service life and possibly gouge the workpiece surface. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only Makita carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Hex wrench Joint Part No. 41 0899-9 Part No.783204-6 Nylon brush wheel Part No. Grit Width 794384-3 120 mm (4-3/4") If the sanding action of the nylon brush wheel begins to diminish, dress the wheel by sanding soft wood for several minutes. . Wheel 120-40 Part No. 794381-9 Part No. 794380-1 Cotton buff wheel 120 0 Wire brush wheel 120 Part No. 794382-7 WHEEL SANDER Model 9741 Q Note: The switch, noise suppressor and other part configurations may differ from country to country. MODEL 9741 om -28-'88 us $zD DESCRIPTION MACHINE 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 ~ 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 4 1 1 2 1 1 1 1 1 1 MACHINE ~ 10 11 12 13 14 15 16 6 1 7 1 8 1 9 1 1 1 3 1 1 1 1 17 18 I : 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1 1 1 1 1 1 1 1 1 3 1 1 2 1 1 Pan Head Screw M5x2B Gear Housing Cover Rubber Pin 4 Ball Bearing 6001LLB Flat Washer 12 Helical Gear 53 Retaining Ring S -15 Ball Bearing 6OOZDDW Spindle Key 4 Gear Housing Pan Head Screw M5x14 Grip Wheel Bearing Retainer 44 Ball Bearing 6003DDW Countersunk Head Screw M4x14 Insulation Washer Ball Bearing 608LL8 Rubber Pin 4 ARMATURE ASSEMBLY [With Item 1...

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories