Évaluations - 2, GPA: 4
(
)
)
|
Photos et spécifications Makita 9207SPB |
Facilité d'utilisation
If you use this tool unsafely or incorrectly, you can suffer seri ous personal injury. 1. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 2. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 3. Check the backing pad carefully for cracks, damage or deformity before operation. Replace cracked, damaged or deformed pad immediately. 4. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a polisher frequently kick and cause loss of control leading to personal injury. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Make sure the abrasive disc or wool bonnet is not contacting the workpiece before the switch is turned on. 8. When sanding metal surfaces, watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 9. Do not leave the tool running. Operate the tool only when hand-held. 10. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 11. Check that the workpiece is properly supported. 12. Pay attention that the wheel continues to rotate after the tool is switched off. 13. This tool has not been waterproofed, so do not use water on the workpiece surface. 14. Ventilate your work area adequately when you perform sanding operations. 15. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 2 1. Switch trigger 2. Lock button 003437 L H ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. Speed change For sanding operations, use the high-speed setting “H” for maximum performance. For polishing and buffing operations, use the low-speed setting “L” for suitable speed range. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 1 1 Grip 003445 Installing side grip (auxiliary handle) CAUTION: • Always be sure that the side grip is installed securely before operation. Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. 003455 Installing or removing abrasive disc Mount the rubber pad onto the spindle. Fit the abrasive disc on the rubber pad and screw the lock nut onto the spindle. 1 3 2 1. Lock nut 2. Abrasive disc 3. Rubber pad 1 2 1. Lock nut wrench 2. Wrench 003456 To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in reverse. 1 2 3 1. Wool bonnet 2. Lock nut 3. Rubber pad 003461 Installing or removing the wool bonnet (optional accessory) Mount the rubber pad onto the spindle. Screw the lock nut onto the spindle. To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. 2 Fit the wool bonnet completely over the rubber pad and pull the string tight. Tie a bow knot and tuck the knot and any loose strings between the wool bonnet and the rubber pad. To remove the wool bonnet, follow the installation procedure in reverse. OPERATION 15 003471 003475 15 MAINTENANCE Sanding operation CAUTION: • Always wear safety goggles or a face shield during operation. • Never switch on the tool when it is in contact with the workpiece, it may cause an injury to operator. • Never run the tool without the abrasive disc. You may seriously damage the pad. Hold the tool firmly. Turn the tool on and then apply the abrasive disc to the workpiece. In general, keep the abrasive disc at an angle of about 15 degrees to the workpiece surface. Apply slight pressure only. Excessive pressure will result in poor performance and premature wear to abrasive disc. Polishing oper...