Évaluations - 2, GPA: 3.5
(
)
)
|
Photos et spécifications Makita BO5012 |
Facilité d'utilisation
Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. Refer to the figure below for the relationship between the number setting on the adjusting dial and the kind of work. 002530 12000 4000 Orbits per minute A B C 1 2 345 Dial setting A range: For polishing B range: For finish sanding C range: For regular sanding NOTE: • The above figure shows standard applications. They may differ under certain conditions. 002531 Emptying dust bag When the dust bag is about half full, switch off and unplug the tool. Remove the dust bag from the tool. Then remove the dust nozzle from the dust bag after unlocking the dust nozzle by turning it slightly counterclockwise. Empty the dust bag by tapping it lightly. 1 1. Dust nozzle 1 1. Dust nozzle 002532 After emptying the dust bag, install the dust nozzle on the dust bag. Turn the dust nozzle slightly clockwise to lock it in place. Then install the dust bag on the tool as described in ’’Installing dust bag’’. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 002533 Installing or removing abrasive disc To install the abrasive disc, first remove all dirt or foreign matter from the pad. Then attach the abrasive disc to the pad, using the hook-and-loop system of the abrasive disc and the pad. Be careful to align the holes in the abrasive disc with those in the pad. CAUTION: • Always use hook-and-loop system abrasive discs. Never use pressure-sensitive abrasive discs. 1 1. Abrasive disc 1. Skirt 1 2 002535 1. Skirt 1 2 002535 002534 Installing dust bag Install the dust bag on the tool so that the Makita logo on the dust bag will be upright (not upside down). The dust bag can be swiveled 360°. Position the skirt so that the dust bag will not interfere with your work. 2. Dust bag OPERATION Sanding operation Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece sur-face. Keep the pad flush with the workpiece and apply slight pressure on the tool. CAUTION: • Never run the tool without the abrasive disc. You may seriously damage the pad. • Never force the tool. Excessive pressure may decrease the sanding efficiency, damage the abrasive disc or shorten tool life. Polishing operation CAUTION: • Use only a Makita genuine sponge pad, felt pad or wool pad (optional accessories). • Always operate the tool at low speed to prevent work surfaces from heating abnormally. • Never force the tool. Excessive pressure may decrease the polishing efficiency and cause motor overload, resulting in tool malfunction. . Applying wax Use an optional sponge pad. Apply wax to the sponge pad or work surface. Run the tool at low speed to smooth out wax. NOTE: • First, wax a not conspicuous portion of the work surface to make sure that the tool will not scratch the surface or result in uneven waxing. • Always run the tool at low speed. Running it at high speed may cause the wax to spatter. 2. Removing wax Use an optional felt pad. Run the tool at low speed to remove wax. 002537 002538 3. Polishing Use an optional wool pad. Run the tool at low speed and apply the wool pad gently to the work surface. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Hook-and-loop system abrasive disc (with pre-punched holes) • Hook-and-loop system sponge pad • Hook-and-loop system felt pad • Hook-and-loop system wool pad Memo Memo Memo Cut Cut s Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How did you learn about this product: ) Magazine Radio From Dealer Exhibition Newspaper From Friend Store Display Previous Usage Catalog Other ( ) 4. Most favored points are: Design Repair Service Features Durability Size Power Price Other ( ) Makita Brand BE SURE TO COMPLETE THE CUSTOMER’S PORTIO...