Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
A worn out grinding wheel 4 needs to be replaced. This is necessary when the specified gap cannot be achieved even after readjusting the positions of the workpiece/tool rest 5 and/or the eye guard mount 2 . Preparing for first use Switching on and off The voltage must agree with that shown on the device rating plate (devices shown as 230 V can also be connected to a 220 V supply). GB/IE/CY Preparing for first use / Maintenance and cleaning Switching on j Press the ON / OFF switch 9 into the „1“ position to switch the device on and run it at a constant speed Switching off j Press the ON / OFF switch 9 into the „0“ position to switch the device off. Grinding a workpiece j Switch on the machine as described above. j To grind metal tools or metal items, place the workpiece on the workpiece/tool rest 54 . and slowly bring it up to the grinding wheel j Press the workpiece carefully against the grinding wheel 4 . Pressing too hard can overload the device. When grinding always use the circumferential end face (not the sides) of the grinding wheel only (See Figures D, E, F). Replacing a grinding wheel Attention! Before carrying out any tasks on the device itself and when you are not using the device, always pull the mains plug out of the mains socket. J Do not use damaged grinding wheels. J Only use grinding wheels with details that correspond with those given on the device rating plate. The circumferential speed should be equal to or greater than the value given on the device rating plate. j Only grinding wheels with markings indicating the manufacturer, the type of adhesive, dimensions and permitted circumferential speed are to be used. If you install new grinding wheels carry out a ringing test before use. Grinding wheels in good condition give a clear ringing noise when struck lightly with a plastic hammer. 1) Take off the outer part of the wheel guard cover 7 by unscrewing the 3 threaded fixings (see Figs. N, O). 2) Release the nut 13 and then remove the outside flange 12. 3) Now replace the grinding wheel and reassemble all the components in the reverse order. Take note that the left-hand side of the double grinding machine has a left-hand thread 11 and the right-hand side has a right-hand thread. This ensures that the nuts can only be screwed off in the direction of rotation of the spindle. j Use only the supplied flanges to mount the grinding wheels. Note: The grinding wheels are fitted with a .“ adapter so that they can be used with grinding wheels purchased later with either a .“, or a 20 mm bore. Grinding wheels are available in various grit grades and hardnesses. The central fixing holes in grinding wheels must not be redrilled. Original accessories / attachments J Use only the accessories and attachments detailed in the operating instructions. The use of inserted tools or accessories other than those recommended in the operating instructions could lead to you suffering an injury. Maintenance and cleaning Attention! Before carrying out any tasks on the device itself and when you are not using the device, always pull the mains plug out of the mains socket. The device is largely maintenance-free. j Clean the device frequently. For best results, clean the double grinding machine immediately after you have finished using it. j Do not allow any liquids to enter the device. Use a dry cloth to clean the device. j Do not under any circumstances use petrol or GB/IE/CY Maintenance and cleaning/Disposal/Information strong solvents. j Store the device in a dry room. Disposal The packaging is wholly composed of environmentally-friendly materials that can be disposed of at a local recycling centre. Do not dispose of electrical power tools with the household rubbish! In accordance with European Directive 2002/96/EC (covering waste electrical and electronic equipment) and its transposition into national legislation, worn out electrical power tools must be collected separately and taken for environmentally compatible recycling. Contact your local refuse disposal authority for more details of how to dispose of your worn out electrical devices. Information Service centre The service centre for your country is shown in the warranty documentation. J Have your device repaired only by qualified specialist personnel using original manufacturer parts only. This will ensure that your device remains safe to use. J If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your device remains safe to use. Declaration of Conformity/ Manufacturer We, Komperna. GmbH, Burgstr. 21, D-44867 Bochum, Germany, declare that this product complies with the following EU directives: Machinery Directive (98/37/EC) EU Low Voltage Directive (2006/95/EC) Electromagnetic Compatibility (89/336/EEC, 93/68/EEC) Type / device description: Parkside double grinding machine PDS 200 A Bochum, 31.08.2007 Hans Komperna. - Managing Director We reserve the right to make...