Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Introduction The MS2000 is a complete sanding kit that allows you to choose between 4 different sanding configurations to do a variety of tasks. Combining the versatility with the Smart SelectTM feature, the sander gives you optimal results. Assembly Warning: Before assembly, make sure that the tool is switched off and unplugged. Removing sanding bases - Figure B • To remove the sanding base, press the release button (3) and pull the base (6) off the tool. B3 6 Random orbit sanding base With this sanding base, you can use the tool as a random orbit sander. Attaching the random orbit sanding base - Figure C • Hold the tool and the sanding base (4) facing upwards as shown in figure C. • Align the dust openings (9) in the sanding base with the dust openings (10) in the tool base. • Press in on the sanding base until you hear it click into place. Fitting sanding sheets - Figure D • Hold the tool with the sanding base (4) facing upwards. • Place the sanding sheet (11) onto the sanding base (4) making sure the holes in the sheet line up with the holes in the base. Large detail sanding base With this sanding base, you can use the tool as a detail sander or a flush sander. Attaching the large detail sanding base - Figures E & F For detail sanding, the pointed end should face forward as in figure E. For sanding large areas, the pointed end should face to the back as in figure F. • Attach the sanding base as described above under “Attaching the random orbit sanding base” • Press in on the sanding base until you hear it click into place. 7 C 4 9 9 10 4 11 D E F 8 Fitting sanding sheets - Figure G • Detach the two diamond-shaped tips (12) from the sanding sheet (13). • Hold the tool with the sanding base facing upwards. • Place the sanding sheet (13) onto the sanding base, making sure that the holes in the sheet line up with the holes in the base. The diamond-shaped tip (12) can be reversed and replaced when worn. • When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again. • When the whole tip (12) is worn, remove it from the sanding base and fit a new tip (12). Tip of the sanding base - Figure H When the sanding tip (14) is worn, it can be reversed as shown in figure H. • The tip (14) can be removed and reversed. Finger attachment - Figure I The finger attachment is used for fine detail sanding. • Remove the screw (15). • Remove the sanding holder tip (7) from the sanding base. • Fit the finger attachment (8) onto the sanding base. • Fit and tighten the screw (15). • Fit the appropriate sanding sheet (16) onto the finger attachment. Operation Let the tool work at its own pace. Do not overload. Warning: Do not cover the ventilation slots when using the tool. Make sure that the sanding base is flat on the workpiece. Switching on and off - Figure J • To switch the tool on, set the on/off switch (1) to position I. • To switch the tool off, set the on/off switch to position O. 13 12 14 15 15 7 8 16 G H I J 1 9 Smart Select Technology - Figure K This sander is fitted with a smart select dial (2) which depicts various sanding applications. They are used to select the proper operating mode for your particular sanding application. Step 1: Using the Smart Select dial (2) choose the application that you are going to perform; detail sanding (3), corner sanding (4), flush sanding (5), random orbit sanding (6). Step 2: Once your application is selected, the window below (7) will recommend the correct base that should be used and identifies the corresponding sanding speed (which is automatically set for you). Step 3: Snap on the recommended base (using the picture and color recommendation in window 7). Note: You can override the speed at anytime by moving the Smart Select dial clockwise for increased speed. Automatic brake system (ABS) This tool has an automatic brake system. When the tool is not on the work surface, this feature keeps the speed of the disc below the speed of the motor. When the tool is switched off, the disc will stop very quickly. Dust Collection WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust canister or elsewhere and cause fire. To reduce risk, empty canister frequently and strictly follow sander manual and coating manufacturer's instructions. CAUTION: When working on metal surfaces, do not use the dust canister or a vacuum K SMART SELECT TECHNOLOGY CHART Setting Application Recommended Base Base Color Speed Setting 2 3 4 5 6 7 Sanding tight and hard to reach areas. Light, detail sanding. Detail finger attachment Orange (1) Low Large detail base - tip facing forw...