Évaluations - , GPA: ( )

Instructions Porter-Cable, Modèle 332

Fabricant : Porter-Cable
Taille : 241.1 kb
Nom Fichier : 5cd2b2be-eea3-41d2-9a2e-fa089d624901.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

KEEP FOOD AND DRINK out of the work area. Wash hands, arms, and face and rinse mouth before eating or drinking. Do not smoke or chew gum or tobacco in the work area. 8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate detergent or trisodium (TSP) to wash and mop areas. 9. AT THE END OF EACH WORK SESSION put the paint chips and debris in a double plastic bag, close it with tape or twist ties and dispose of properly. 10. REMOVE PROTECTIVE CLOTHING and work shoes in the work area to avoid carrying dust into the rest of the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash hair and body thoroughly with soap and water. REPLACEMENT PARTS When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating. CAUTION: Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool. EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes. If an extension cord is to be used outdoors it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use. RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. Nameplate Ampere Rating 0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 6 6-8 18 16 12 10 10 8 6 6 6 8-10 18 14 12 10 8 8 6 6 4 10-12 16 14 10 8 8 6 6 4 4 12-14 16 12 10 8 6 6 6 4 2 14-16 16 12 10 8 6 6 4 4 2 16-18 14 12 8 8 6 4 4 2 2 18-20 14 12 8 6 6 4 4 2 2 6 900006 - 02-07-02.qxd 10/15/02 2:25 PM Page 7 FUNCTIONAL DESCRIPTION FOREWORD The Porter-Cable Random Orbit Sanders provide rapid stock removal with 80 to 100 grit paper and swirl-free finishing with 120-150 grit paper. Model 332 is equipped to accept 5" diameter STIKIT™ adhesive paper backed abrasives. Model 333 is equipped to accept 5" hook & loop backed abrasives with five dust extraction holes. Model 333VS is equipped to accept 5" hook & loop backed abrasives with five or eight dust extraction holes. Model 334 is equipped to accept 5" diameter STIKIT™ adhesive backed abrasives with five dust extraction holes. TO START AND STOP SANDER 1. CAUTION: Make certain the switch is in the “OFF” position, and the power source is the same as that specified on the tool’s nameplate. 2. Connect the tool to the power source. CAUTION: Keep hands and body parts away from rotating disc. Contact with rotating disc can cause severe cuts and abrasions. 3. The switch button, (A) Fig. 1, is labeled “ON” and “OFF”. Depress the “ON” end of the switch button to start motor. Depress the “OFF” end of the switch button to stop motor. SPEED CONTROL (333VS) Model 333VS is equipped with a variable speed control. Operating speed is adjustable between 5000 OPM (Orbits Per Minute) and 12000 OPM. Adjust speed by turning thumbwheel (B) Fig. 1A. Thumbwheel position #1 provides the slowest operating speed (5000 OPM) and position #6 the fastest (12000 OPM). Speed may be changed while motor is running or while it is stopped. A A B Fig. 1 Fig. 1A ASSEMBLY INSTALLING/REMOVING ABRASIVE DISC Models 332 and 334: 1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE. 2. Place machine on workbench with pad up (see Fig. 2). 3. Clean dust from pad face. 7 900006 - 02-07-02.qxd 10/15/02 2:25 PM Page 8 Fig. 2 Fig. 3 4. Tear a new abrasive disc from roll and position disc to the sander pad. Align the dust extraction holes in paper with holes in pad (334 ONLY). 5. Press disc firmly onto pad. 6. Position machine with abrasive contacting scrap material. Start machine and operate momentarily while exerting firm pressure to seat disc to pad. CAUTION: Failure to properly seat disc to pad may result in disc being thrown from pad causing personal injury. 7. To remove disc, peel disc away from pad. NOTE: Do not store machine with an abrasive disc installed. Heat generated by the sa...