Évaluations - 3, GPA: 5
(
)
)
|
Photos et spécifications Festool DELTEX DX 93 E |
Facilité d'utilisation
of strokes 10 000 - 19 400 spm Abrasive stroke 2.5 mm (0.1 in.) Weight 1.5 kg (3.3 lbs.) Safety UL 745, CSA C22.2 No. 745 Symbols V Volts A Amperes Hz Hertz W Watt ~ Alternating current n0 No load speed Class II Construction rpm Revolutions per minute spm strokes per minute O Diameter Intended use The Deltex sander can be used to smooth wood, plastics, metal, steel, composite materials, paint- lacquers, filler, stopper and similar materials. Thanks to the triangular shape of the sanding pad the machine is particularly suitable for processing tricky corners, edges and grooves. If explosive or self-igniting dusts are produced during the sanding of certain materials the manufacturer’s processing instructions must be observed. The user is liable for damage and injury resulting from incorrect usage! Electrical connections and starting The mains voltage must comply with the voltage specified on the ratings plate! 3 1.1 1.2 1.1 1.2 Push the switch (1.1) forwards to start the machine. A slight pressure on the rear of the switch is enough to switch the machine off. When cold the machine may take a few minutes to reach maximum speed. This is due to its construction and is not serious. Electronics ELECTRONIC When processing different surfaces it is helpful to adjust the sanding speed to the respective material. The figures on the speed regulator (1.2) roughly correspond with the following idling speeds: strokes per min 1 10 000 4 15 400 2 11 800 5 17 200 3 13 600 6 19 400 Metalworking Observe the following safety precautions when working on metals: • Pre-connect a residual current circuit-breaker (FI, PRCD). • Connect the tool to a suitable dust extractor. • Regularly clear out any dust accumulations in the motor housing. • Wear protective goggles. Tool settings Always remove the power plug from the socket before carrying out any work on the power tool. Dust extraction 2.1 In order to draw off the dust produced during sanding the hose (O 27 mm) of a Festool dust extractor is attached to the suction adapter (1.2) at the end of the motor casing. The sanding dust is then drawn off directly through the extractor channel in the sanding pad. When working with wood or if materials are used which may produce harmful dusts the electrical tool should be connected to a suitable extractor. Sanding pad 3.1 3.2 3.3 3.4 3.5 The sanding pad is made of MPE foam (micro-cellular polyurethane elastomer) and has bevelled edges (3.3). It has a velour fabric on its top surface and a Stickfix covering on its underside. The velour side of the sanding pad is pressed against the Stickfix covering of the sanding base (3.4) The tool’s sanding base has three centring protuberances (3.1) at its corners enabling easy adjustment. Please note: The device has been specially developed for work in corners and on edges. Experience has shown that this leads to a more point-focal load on the tip of the sanding base. The heat generated is naturally higher than when working on the whole surface since the same pressure is applied to a smaller surface. Do not apply as much pressure since otherwise the Stickfix covering of the sanding pad and the abrasive quickly become damaged. If the Stickfi x covering on the front tip of the sanding pad should become worn simply remove the sanding pad, rotate around 120° and replace. If the Stickfix covering of the sanding base should become worn the complete base (487406) can be replaced. Simply loosen the two screws (3.2 and 3.5). Abrasive Festool can offer perforated Stickfi x abrasives in grain sizes from P 40 to P 400 for an effective 4 dust extraction. Order numbers can be found in the corresponding brochures. The Stickfix abrasives are simply pressed onto the Stickfix sanding pad and pulled off after use. If the front tip of the abrasive has become worn it can be removed from the sanding pad, rotated around 120° and replaced. Systainer Many Festool products are shipped in a unique system container, called "Systainer". This provides protection and storage for the tool and accessories. The Systainers are stackable and can be interlocked together. They also can be interlocked atop Festool CT dust extractors. 4.3 4.2 4.1 -Place one systainer on top of the other. -Release all four latches on the lower systainer by pulling back at their top edges (4.1). -Slide all four latches upward (4.2). -Snap all four latches back to their fl at position (4.3) so they engage the stacking tabs of the upper systainer. Maintenance and care Always disconnect the machine at its mains plug before performing maintenance work! Any maintenance and repair work requiring the motor casing to be opened may only be carried out by an authorised service workshop. The vent openings on the motor casing must always be kept clean and free to ensure a good circulation of air. The device is fitted with self-disconnecting special brushes. If these become worn the power is automatically interrupted and the device comes to a standstill. Any maintenance and repai...