Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
You can stop recording using either of the following methods. A. Press the START/STOP switch in the SEQUENCER section. B. Press the START/STOP switch in the RHYTHM section. Note: You can stop recording by pressing the INTRO/ENDING switch in the RHYTHM section if both of the PLAY and REC switches for TRACK 2 are OFF. (For Examples 2 and 3.) 15 ■ Recording on TRACK 2 1. Press the TRACK 2 REC switch. Lights - TRACK 2---------- | RHYTHM A PA ■ Q ^ D — I CIinnZD Pi. AY REC I i The AUTO PLAY ACCOMPANIMENT function is automatically turned on and the SPLIT POINT is automatically set To change the SPLIT POINT, you have to first turn off the REC switch Note: * The AUTO PLAY ACCOMPANIMENT cannot be turned OFF while you are recording on TRACK 2 *To change the SPLIT POINT, refer to page 6. To record on TRACK 1 at the same time, press the TRACK 1 REC switch after setting the desired tone Note: In this case, recording on TRACK 1 in the SPLIT mode is not possible. 2. Select a RHYTHM. Note: For the procedure to select a RHYTHM, see page 8. Press the VARIATION switch whenever you desire. 3. Adjust tempo and volume balances. o o o o rhvthm volume Listen to the metronome to adjust the tempo. Note: ‘Variation of tempo and balance during playing are also recorded. * You can change the tempo and volume during playback. However, when a recorded change in tempo or volume is played back your manual change is cancelled, and the tempo or volume as recorded becomes effective for playback. 4. Set the recording level for TRACK 2. 5. Start recording. You can start recording using either of the following methods. A. Start playing by pressing either the START/STOP switch or the INTRO/ENDING switch in the RHYTHM section. Note: * Recording starts as soon as you press the switch. *lf you start recording by pressing the START/STOP switch in the SEQUENCER section, AUTO PLAY ACCOMPANIMENT does not start, even when you strike a chord. Therefore, recording on TRACK 2 is not possible. 16 B. Start playing by pressing the SYNC START switch in the RHYTHM section. Note: RHYTHM and AUTO PLAY ACCOMPANIMENT start when you strike a key. Recording starts at the same time. 6. Stop recording when you finish playing. You can stop recording using either of the following methods. A. Press the START/STOP switch in the SEQUENCER section. B. Press the START/STOP switch or the INTRO/ENDING switch in the RHYTHM section. To pause the recording ... 1. Press the PAUSE switch if you want to pause the recording temporarily. o • The LED above PAUSE switch lights during the PAUSE Note: During the PAUSE, it is possible to change from playback to recording only for TRACK 1 (not for TRACK 2) This function can be used to record your playing again from some halfway point if you initially failed to record your playing. 2. To cancel the PAUSE, press the PAUSE switch again. Note: The START/STOP switch in the RHYTHM or the SEQUENCER section cannot be used to cancel the PAUSE. If you press the START/STOP switch, the recording is stopped. Striking a key also cancels the PAUSE and restarts the recording. 5-2. Playback After you've recorded your playing, play it back and listen to the music you created. 1. Press the PLAY switch for the track you want to play back. Note: If you want to listen to the recorded sounds on both tracks, press the PLAY switch for both tracks. The LED above the PLAY switch lights (standby state). 2. Set the volume for playback. Note: The VOLUME slide control in the SEQUENCER section are used for both input level adjustment for recording, and for output level (volume) adjustment during playback. Lights -TRACK 1- I-1 * ° I D H C=~) [-I iilllilil VOLUME PLAY REC I I I I I I I I I VOLUME PLAY REC 17 3. Press the REPEAT switch to repeat the playback. Lights o • m ci MERGE t- 2 REPE^ While the repeat function is on (REPEAT LED lit), sounds are played back again from the beginning, several seconds later after playback is completed Note: If you have pressed the PLAY switch for both TRACK 1 and TRACK 2, playback is repeated for both TRACK 1 and TRACK 2 after playback of the longest recorded track has been completed. 4. Start the playback. You can start playback using either of the following methods. A Press the START/STOP switch in the RHYTHM section Note: When you press the START/STOP switch in the SEQUENCER section, only sounds on TRACK 1 are played back Playback from TRACK 2 is not possible even if you have pressed the PLAY switch for TRACK 2 B After pressing the SYNC START switch in the RHYTHM section, strike a key Note: The INTRO/ENDING switch cannot be used for starting and stopping the playback Touch, tempo and volume balance are reproduced in playback as they were recorded. Note: For playback from both TRACKs 1 and 2, sounds are reproduced according to the tempo recorded on whichever track was recorded last. You can change tempo and volume as required. 5. To pause the playbac...
Ce manuel est également adapté pour les modèles :Synthétiseur / piano, - Digital Piano PV10 (1.25 mb)