Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Synthétiseur / piano, - CP5 (160.21 kb)
Synthétiseur / piano, - CP5 (3.13 mb)
Facilité d'utilisation
The same operation can be performed using the Split parameter from the Common Settings screen. 8 [VOICE] button (page 33) Press this button to open the parameter setting screen for the currently selected part’s Voice block. The lamp to the top-left of the button lights up whenever this screen is being displayed. 4 3 5 6 7 8 ! @ # & 9 ) $ % ^ * 1 2 A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 ( CP5 only Control Panel CP5/CP50 Owner’s Manual 11 Component Names & Functions 9 [STORE/ASSIGN] button (pages 28 , 50) Press this button to call up a screen for storing Performances and system settings. In addition, by pressing and holding the [STORE/ASSIGN] button (for at least one second) within the Performance screen or a parameter setting screen (for any block other than the Master Equalizer or Master Compressor), you can call up a screen for directly assigning each of the Knobs 1 to 3 (see ( below) to block parameters. ) [COMMON] button (page 35) Press this button to open the parameter setting screen for the Common Settings area, which affects each of the left and right parts in the same way. The lamp to the top-left of the button lights up whenever this screen is being displayed. ! [PRE-AMP] button (pages 31, 34) @ [MOD-FX] button (pages 31, 34) # [PWR-AMP] button (pages 31, 34) $ [REVERB] button (pages 31, 35) Press these buttons to toggle on and off the Pre-Amplifier block, Modulation Effect block, or Power-Amplifier / Compressor block (CP5 only) for currently-selected part or the Reverb block. The lamp to the top-left of each button lights up whenever the corresponding block is turned on. It should be noted, however, that the Pre-Amplifier block has an effect on the sound only if a voice from the PIANO or E.PIANO category has been selected for the part in question. Furthermore, if you press and hold one of these buttons (for at least one second), the parameter setting screen for the corresponding block will be displayed, and the lamp to the top-left of the button will start to flash. Even if a block’s parameter setting screen is being displayed, it can still be toggled on and off by pressing the corresponding button. It should be noted that these lamps will flash in one of two different ways to indicate whether the block is on or off; specifically, the lamp stays lit longer when the block is on, and it stays off longer when the block is off. % [SONG SETTING] button (page 37) Press this button to open the Song Setting screen. The lamp to the top-left of the button lights up whenever this screen is being displayed. ^ [REC] button (page 41) Press this button to open the Record screen. The lamp to the top-left of the button lights up whenever this screen is being displayed. & Sequencer Transport buttons (pages 37, 42) Use these buttons to control the recording and playback of backing tracks. [LL] (Rewind) button Whenever you are using a Preset Drum Pattern or a User Song as the backing track, pressing this button will move the play position back by one measure at a time. Alternatively, if you are using a Wave file as the backing track, pressing this button will move the play position back by one second at a time. Press and hold the button to rewind continuously. B C E H J A D F G I K L B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7 CP5 only Compone nt Names & Functions Component Names & Functions [ RR ] (Fast Forward) button Whenever you are using a Preset Drum Pattern or a User Song as the backing track, pressing this button will move the play position forward by one measure at a time. Alternatively, if you are using a Wave file as the backing track, pressing this button will move the play position forward by one second at a time. Press and hold the button to fast-forward continuously. [J ] (Stop) button This button is used to stop recording or playback. [R /K ] (Play / Pause) button This button is used to start recording or playback. In addition, if playback is underway, this button can be pressed to pause it. Pressing this button when recording is underway ends the recording. * Display Using the display, you can confirm system messages, set parameters, and perform a range of other operations. ( Knobs 1 to 3 (page 27) Numbered 1 to 3 from left to right, these knobs can be turned to control the parameters assigned to them. On each different parameter setting page, furthermore, a different set of parameters or operations is assigned to the knobs, and they can be turned or pressed to set the parameters or perform the operations. A [L PAGE] and [PAGER ] buttons (page 19) Press these left and right buttons within a parameter setting screen that comprises a number of different pages in order to navigate between them. B [EXIT/jump to edit] button (pages 21, 34) Press this button to return to the Performance screen from the parameter setting screen for the currently selected block (page 31), from the Utility screen, or from the File screen. Furthermore, b...
Ce manuel est également adapté pour les modèles :Synthétiseur / piano, - CP50 (9.6 mb)