Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Do not put hands or other objects into fan housing. Keep hands and feet away from rotating impeller. APPLICATIONS With Turbo Blower Add-On: • Up to 145 MPH Velocity Air Flow for Fast Clearing of Large Areas. • Flare Nozzle for Large Areas. • Concentrated Nozzle for Hard to Reach Places. Shaft Housing Hanger Housing/Air intake Concentrator Nozzle Flare Nozzle KNOW YOUR UNIT RULES FOR SAFE OPERATION APPLICATIONS With Turbo Blower Add-On: • Up to 145 MPH Velocity Air Flow for Fast Clearing of Large Areas. • Flare Nozzle for Large Areas. • Concentrated Nozzle for Hard to Reach Places. Shaft Housing Hanger Housing/Air intake Concentrator Nozzle Flare Nozzle KNOW YOUR UNIT RULES FOR SAFE OPERATION OPERATING INSTRUCTIONS ASSEMBLING THE COUPLER The following Troy-Bilt Add-Ons are also available for your unit: Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBBV Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBGC Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBHS Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBLE Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . .TBSS Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBST Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBTP Removing the add-on WARNING: Read and understand operator’s manual for unit to be used with this add-on prior to operation. 1. Turn the knob counterclockwise to loosen (Fig. 1). 2. Press and hold the release button (Fig. 1). 3. While firmly holding the upper shaft housing, pull the turbo blower add-on out of the coupler (Fig. 2). Installing the add-on WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing add-ons. NOTE: Aligning the release button with the guide recess will help installation (Fig. 1). Release Button 4. Turn the knob clockwise to tighten (Fig. 3). Primary Hole Upper Shaft Housing Fig. 2 Lower Shaft Housing Knob Coupler CAUTION: Lock the release button in the primary hole (Fig. 2) and securely tighten the knob before operating this unit. Knob Fig. 3 CAUTION: The add-ons with the coupler system are to be used in the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. The turbo blower add-on should be installed with the release button in the primary hole. Check Flex Shaft Engagement Prior to Using 1. Start the unit. 2. Briefly engage and release the trigger. 3. Check that add-on is operating. 4. If the add-on is not operating, remove add-on and repeat steps for installing the add-on. 5. Recheck operation of add-on attachment. NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench. 1. Remove the hanger from the top of the shaft housing. 2. Turn knob counterclockwise to loosen (Fig. 1). 3. While firmly holding the add-on, push it straight into the coupler (Fig. 2). Release Button ClockwiseCounterclockwise Coupler Guide Recess Knob Fig. 1 Indexing Button on inside of nozzle Flare Nozzle Indexing Button on inside of nozzle Concentrator Nozzle Indexing Button Detent Indexing Button OPERATING INSTRUCTIONS Fig. 4 Fig. 5 Fig. 6 Fig. 7 8 INTERCHANGING NOZZLES Use the following instructions to attach or interchange the two nozzles (Figs. 4 and 5). INSTALLING FLARE OR CONCENTRATOR NOZZLE ONTO BLOWER HOUSING 1. Align the indexing button on the inside of the nozzle with the detent on the housing (Fig. 6). 2. Push the nozzle onto the housing and turn the nozzle clockwise until it locks (Fig. 7). NOTE: Make sure the nozzles are installed properly, with indexing button facing up, before operating the unit. WARNING: To avoid serious personal injury, do not insert hands into nozzles when removing or installing them. WARNING: To reduce the risk of injury, disconnect power source before removing nozzles. WARNING: The nozzles may become worn and get sharp edges due to rubbing on the ground. It is suggested to use gloves when changing nozzles. REMOVING FLARE OR CONCENTRATOR NOZZLE FROM BLOWER HOUSING 1. Grasp the nozzle and turn it counterclockwise approximately 45° until the indexing button on the inside of the nozzle snaps out of the detent in the blower housing (Fig. 8). Pull the nozzle off of the blower housing. Detent Indexing Button Fig. 8 Fig. 10 Fig. 9 9 OPERATING INSTRUCTIONS USING THE FLARE NOZZLE Use the flare nozzle for large, hard surfaces such as driveways and sidewalks (Fig. 9). USING THE CONCENTRATOR NOZZLE Use the concentrator nozzle for hard to reach places such as corners in a garage or to control dust in a dust laden environment (Fig. 10). MAINTENANCE AND REPAIR INSTRUCTIONS STORAGE • Check unit before storage to be sure the equipment is in safe working condition. • Stop the engine or motor. • Store the unit indoors, in a dry and locked place, out of the ...
Ce manuel est également adapté pour les modèles :Les systèmes de ventilation - TBTB (1.09 mb)