Évaluations - , GPA: ( )

Instructions Air King, Modèle B900

Fabricant : Air King
Taille : 143.01 kb
Nom Fichier : ea86764e-d191-4606-973b-04f4dba72a4b.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK 5. Sufficient air is needed for proper combustion and exhausting of AND INJURY TO PERSON, OBSERVE THE FOLLOWING: gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s 1. Read all instructions before installing or using range hood. guideline and safety standards such as those published by the National Fire Protection Association (NFPA) and the American 2. Use this unit only in the manner intended by the manufacturer. If Society for Heating, Refrigeration, and Air Conditioning Engineers you have questions, contact the manufacturer. (ASHRAE), and the local code authorities. 3. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE from being switched on accidentally. When the service TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS. disconnecting means cannot be locked, securely fasten a prominent 6. To avoid motor bearing damage and noisy and/or unbalanced warning device, such as a tag, to the service panel. impellers, keep drywall spray, construction dust, etc. off power unit. 4. Installation work and electrical wiring must be done by qualified 7. Refer to the instructions included with the Range Hood Canopy for person(s) in accordance with all applicable codes and standards, additional safety information. including fire-related construction. SAVE THESE INSTRUCTIONS 111597006 New 3-07 1 of 12 INSTALLATION INSTRUCTIONS 3. Lift blower up into the hood canopy and slide the keyhole slots in the blower mounting flange over the two studs of the hood. Slide CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE the blower into place and tighten the hex nuts on the mounting stud PANEL BEFORE STARTING INSTALLATION. while lining up the 8 holes in the blower mounting flange to the 8 screw studs of the hood (Figure 3). WARNING: THIS BLOWER IS INTENDED FOR USE ONLY IN AIR KING PROFESSIONAL SERIES RANGE HOOD CANOPIES MARKED SUITABLE FOR USE WITH THIS BLOWER. DO NOT TO INSTALL IN ANY OTHER APPLICATION. SECTION 1 Preparing for installation NOTE: Before installing blower, make sure range hood canopy is properly installed and securely in place. See “Range Hood Mounting Instructions”. 1. Unpack blower from the carton and confirm that all pieces are present. In addition to the blower you should have: 10 - 8-32 Screws 8 - Washers 1 - Capacitor 4. Using 8 of the included 8-32 screws and washers, mount the blower 2 - #6 Screws in place and tighten all screws. Confirm that the blower is securely 1 - Transformer seated in place and there are no air gaps around the blower gasket. 1 - Fuse 5. Plug the 3 wire quick connect cord from the blower into the 1 -Instruction/Safety Sheet receptacle on the range hood canopy. Plug the 4 wire quick connect 2. The installation of the blower is slightly different from one canopy cord from the blower into the receptacle on the transformer. Plug height to another. For 18" high canopies proceed to Section 2, for the 4 wire quick connect from the transformer into the receptacle10" high canopies proceed to Section 3. on the range hood canopy. These cords will only fit into the receptacles one way (Figure 4). SECTION 2 Installation into 18" High Canopy 1. Install transformer into hood canopy by lining up the 2 holes on the flange of the transformer with the 2 screw studs in the top left side of the hood canopy. Use 2 of the included 8-32 screws to make the connection and fully tighten (Figure 1). Figure 3 Keyholes Stud w/Hex Nuts Screw Stud Figure 1 Transformer Rear Wa...