Évaluations - 5, GPA: 3.2
(
)
)
|
Facilité d'utilisation
Shindaiwa recommends that the unit be returned to your Shindaiwa dealer for service. WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. maintenance intervals /TNENOPMOCMETSYSECNANETNIAMERUDECORPD'QERLLIKSLEVELYLIADROEROFEBESUYREVELEUFER3SHTNOM09ROSRUOH6SHTNOM072ROSRUOHYLRAEYserudecorPecnanetniaMrelaeDindaiwahSdednemmoceRtroPtsuahxErednilyCnobraceD/naelC/tcepsnI3C/IserudecorPecnanetniaMflesruoY-tI-oDretliFriAecalpeR/naelC/tcepsnI1C/I*RekohCnaelC/tcepsnI2C/IretliFleuFecalpeR/tcepsnI1I*RskaeL,metsySleuFecalpeR/tcepsnI1)1(I*)1(R/ImetsySgnilooCnaelC/tcepsnI2C/IrotserrAkrapSrelffuMecalpeR/tcepsnI2*R/IepoRretratSlioceRnaelC/tcepsnI1C/I*R/IgulPkrapSnaelC/tcepsnI2C/I*RstloB/stuN/swercSecalpeR/nethgiT/tcepsnI1*R/ISEDOCRETTELERUDECORPECNANETNIAMNAELC=C,ECALPER=R,TCEPSNI=I: -ETONTNATROPMIderiuqerfoycneuqerfehtenimretedlliwecneirepxerdnaesulautcA.mumixameranwohsslavretniemiT.ecnanetniam:SETONERUDECORPECNANETNIAM)1(.ytirgetninoissimeniatniamotecnanetniamralugereriuqerTONODsknatleufevitaropavewoL*.noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA air filter Level 1. Tools required: 25 - 50mm (1 - 2 in.) cleaning brush NOTE Always brush dirt and debris away from air cleaner area prior to cleaning air filter. Brush dirt off air cleaner area. Keep dirt away from engine and air intake grid. Remove air filter cover. Brush dirt from inside cover and away from edges of air filter. Check air filter seal for tight fit with air filter case. Remove air filter from case. Use care to prevent dirt and debris from falling into air filter case. Inspect filter element and seal. Replace filter if any of these problems are present: •Air filter seal does not fit tightly against case •Air filter seal is distorted, worn, or damaged •Air filter element has holes or other damage •Air filter element is saturated with dirt •Air filter element is soaked with fuel mix If air filter is in good condition and can be cleaned and reused, lightly brush debris from air filter element, or blow filter element clean using low pressure (40 psi or less) compressed air directed at inside of filter. IMPORTANT When using compressed air, always direct air stream at inside surface of filter so dust and debris will be blown out of filter. Keep air nozzle 6 - 8 inches away from filter to prevent damage to filter. Install air filter in case, and replace cover. NOTICE Actual replacement interval for air filter depends on operating conditions. Operation in dustier applications requires more frequent cleaning and replacement. Continued operation with a damaged or excessively dirty filter will allow dirt and debris to enter engine, and result in poor performance, rapid engine wear, and premature engine failure. fuel filter Level 1. Tools required: 200 - 250 mm (8 - 10 in.) length of wire with one end bent into a hook, clean rag, funnel, and an approved fuel container DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. Use the “fuel line hook” to pull the fuel line and filter from the tank. Remove the filter from the line and install the new filter. spark plug Level 1. Tools required: 19mm Spark Plug deep socket, Feeler gauge IMPORTANT Use only BPMR-8Y spark plug otherwise severe engine damage may occur. Remove spark plug , and check for fouling, worn and rounded center electrode. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. Adjust spark plug gap by bending outer electrode. Tighten spark plug to 150-170 kg/cm (130-150 in. lb.). 0.65 mm (0.026 in.) cooling system Level 2. Tools required: 25 - 50mm (1 - 2 in.) cleaning brush, Cross Head Screwdriver Parts Required: None, if you are careful. IMPORTANT To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when: • Air intakes are blocked, preventing cooling air from reaching the cylinder. • Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving. Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance.” Any failure attributed to lack of maintenance is not warranted. Cleaning Grill Remove accumulated debris from intake grill between backpack frame and blower housing. Cleaning Cylinder Fins Remove spark plug and engine cover (four screws), pull cover away from engine. Clean cylinder fins (A) to allow cooling air to pas...
Ce manuel est également adapté pour les modèles :Les systèmes de ventilation - 82050 (8.87 mb)