Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger • Take periodic breaks to minimize repetition and rest your hands. • Reduce the speed and force with which you do the repetitive movement. • Do exercises to strengthen the hand and arm muscles. • Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented. A WARNING Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manuals • Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe Operation. Clear the Work Area • Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use. • Take wind conditions into account: avoid open doors and windows. • Do not point blower at people or animals. Keep a Firm Grip • Hold the front and rear handles with both hands, with thumbs and fingers encircling the handles. Keep a Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach. Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. J 5 English English Equipment check A WARNING Use only Shindaiwa approved attachments. Serious injury may result from the use of a non-approved attachment combination. Shindaiwa, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by Shindaiwa. Read and comply with all safety instructions listed in this manual and safety manual. Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found. Do not use blower if any part is missing or damaged. Have repairs done only by an authorized Shindaiwa Service dealer. Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual. Emission control EPA Phase 2/ C.A.R.B. TIER III The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions). Evaporative emission may be applicable to California models only. important engine information ENGINE FAMILY: 7EHXs.0214EKG Displacement: 21.2 cc emission compliance period : 300 hrs. this ENGINE meets u.s. EPA PH2 EXH and 2007 AND later california exh and evap emission regulations for s.o.r.e.. refer to owner's manual for maintenance specifications and adjustments. m Ktonrrz rrrr An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY; information on label varies by engine FAMILY). PRODUCT EMISSION DURABILITY The 300 hour emission durability period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. 6 Description Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your Shindaiwa dealer. WARNING ik DANGER The muffler or catalytic muffler and surrounding cover may become | iihillllMIIni extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur. Hot Decal (near muffler) 10— General Warning Decal (located on top of blower housing) 1 4 9 Sound Label (located on blower housing) 65 I Category I Measured at 50 ft. (15m) per ANSI B175.2 J 7 English English 1. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop. 2. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique. 3. SPARK PLUG - Provides spark to ignite fuel mixture. 4. SPARK ARRESTOR - CATALYTIC MUFFLER...
Ce manuel est également adapté pour les modèles :Les systèmes de ventilation - EB212 (2.11 mb)