Évaluations - 1, GPA: 4 ( )

Fabricant : Stihl Taille : 1.96 mb Nom Fichier : Langue d'enseignement:

Misaligned, damaged or broken cap N If the cap does not drop fully into the opening when the positioning marks line up and/or if the cap does not tighten properly when twisted, the base of the cap in relation to the top may be prematurely rotated to the closed position. Such misalignment BR 500, BR 550, BR 600 English can result from handling, cleaning or an improper attempt at tightening. 001BA227 KN Left: Base of cap in closed position (with open space) Right: Base of cap correctly positioned for installation 452BA121 KN N To return the cap to the open position for installation, turn the cap (with the grip up) until it drops fully into the tank opening. Next, twist the cap counterclockwise as far as it will go (approx. 1/4 turn) – this will twist the base of the cap into the correct position. Then, twist the cap clockwise, closing it normally. N If your cap still does not tighten properly, it may be damaged or broken; immediately stop use of the unit and take it to your authorized STIHL dealer for repair. See also the "Fueling" chapter in your Instruction Manual for additional information. Before Starting Warning! Always check your power tool for proper condition and operation before starting, particularly the throttle trigger, setting lever and stop switch. The throttle trigger must move freely and always spring back to the idle position. Never attempt to modify the controls or safety devices. Warning! Never operate your power tool if it is damaged, improperly adjusted or maintained, or not completely or securely assembled. Warning! Check that the spark plug boot is securely mounted on the spark plug – a loose boot may cause arcing that could ignite combustible fumes and cause a fire. Keep the handles clean and dry at all times; it is particularly important to keep them free of moisture, pitch, oil, fuel mix, grease or resin in order for you to maintain a firm grip and properly control your power tool. Warning! To reduce the risk of injury from parts thrown by the fan wheel, check the fan housing for damage (cracks or holes that could allow foreign objects to contact the fan wheel). If any such damage is found, stop using the unit and contact your STIHL dealer for repair. Warning! Adjust carrying harness to suit your size before starting work. In an emergency, you may slip out of the harness and throw off the machine quickly. Try slipping out of the harness a number of times before using the machine in order to become accustomed to it. Do not throw off the machine while practicing as it could damage the machine. Starting To reduce the risk of fire and burn injuries, start the engine at least 10 feet (3 m) from the fueling spot, outdoors only. Warning! Your power tool is a one-person machine. To reduce the risk of eye or other injury from thrown objects, insure that bystanders are at least 50 feet (15 m) away during use. Stop operation immediately if you are approached. BR 500, BR 550, BR 600 Warning! This unit is equipped with an ignition system that is normally in operational readiness. After the setting lever is used to stop the engine, it automatically springs back to the "on" position. If the engine is warm, it may be possible to start it by simply pulling the starter rope, with no further adjustments. To reduce the risk of injury, be particularly alert to keep children away from the unit. For specific starting instructions, see the appropriate section of your manual. Place the power tool on firm ground or other solid surface in an open area. Maintain good balance and secure footing. Warning! When you pull the starter grip, do not wrap the starter rope around your hand. Do not let the grip snap back, but guide the starter rope to rewind it properly. Failure to follow this procedure may result in injury to your hand or fingers and may damage the starter mechanism. Once the engine has started, immediately blip the throttle trigger, which should cause the choke knob to move to the run position and allow the engine to slow down to idle. During Operation Holding and Controlling the Power Tool 452BA094 KN The blower is designed for single- handed operation with the right hand on the control handle. It should be carried as a backpack with the straps of the harness over both shoulders. Warning! To reduce the risk of loss of control, never carry the unit with the strap(s) over one shoulder. Wrap your fingers tightly around the handle, keeping the control handle cradled between your thumb and forefinger. Keep your hand in this position to have your machine under control at all times. Warning! Special care must be taken in slippery conditions (wet ground) and in difficult, overgrown terrain. Watch for hidden obstacles such as tree stumps, roots, rocks, holes and ditches to avoid stumbling. For better footing, clear away fallen branches, scrub and cuttings. Be extremely cautious when working on slopes or uneven ground. English To reduce the risk of stumbling and loss of control, do not walk backward while operat...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :