Évaluations - , GPA: ( )

Instructions Poulan, Modèle 966454201

Fabricant : Poulan
Taille : 264.16 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

If the engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE. 7. Once the engine starts, allow it to run 10 seconds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls. STARTING A WARM ENGINE 1. Move the choke lever to the HALF CHOKE position. 2. Squeeze the throttle trigger fully and hold through all remaining steps. 3. Pull starter rope sharply until engine runs, but no more than 6 pulls. 4. Allow engine to run 15 seconds, then move the choke lever to RUN. NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded. STARTING A FLOODED ENGINE Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723. MAINTENANCE WARNING: Avoid touching muffler unless engine and muffler are cold. A hot muffler can cause serious burns. WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts. HELPFUL TIP IMPORTANT: Have all repairs other than the recommended maintenance described in the instruction manual performed by an authorized service dealer. If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your responsibility to maintain and perform general maintenance. --9 GENERAL RECOMMENDATIONS The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjustments will need to be made periodically to properly maintain your unit. CHECK FOR LOOSE FASTENERS AND PARTS S Muffler S Spark Plug Boot S Air Filter S Housing Screws CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. S Fuel Tank - --Do not use unit if fuel tank shows signs of damage or leaks. S Vacuum Bag - --Do not use vacuum bag if it is torn or damaged. INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. - -- CLEAN AIR FILTER CHECK MUFFLER MOUNTING A dirty air filter decreases engine perform-SCREWS ance and increases fuel consumption and Once each year, ensure muffler mounting harmful emissions. Always clean or replace screws are tightened securely to prevent air filter after every 5 hours of operation or damage. yearly, whichever comes first. Cleaning the air filter: MufflerMountingScrew AirFilterCoverAirFilterButton FuelLineFuelFilter --10- MUFFLER AND SPARK ARRESTING SCREEN WARNING: The muffler on this product contains chemicals known to the State of California to cause cancer. NOTE: THE SPARK ARRESTING SCREEN ON THIS UNIT IS NOT SERVICEABLE. For normal homeowner use, the muffler and spark arresting screen will not require replacement. After 50 hours of use, we recommend that your muffler be replaced by your authorized service dealer. CARBURETOR IDLE SPEED ADJUSTMENT The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is re leased. To adjust idle speed: Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow). S Turn idle speed screw clockwise to in crease engine speed if engine stalls or dies. S Turn idle speed screw counterclockwise to decrease engine speed. 1. Clean the cover and the area around it to keep debris from falling into the carburetor chamber when the cover is removed. NOTE: Move choke lever to RUN position before opening air filter cover. 2. Open air filter cover by pushing button (see illustration). Remove air filter. NOTE: Do not clean filter in gasoline or other flammable solvent. Doing so can create a fire hazard or produce harmful evaporative emissions. 3. Wash the filter in soap and water. 4. Allow filter to dry. 5. Apply a few drops of oil to the filter; squeeze filter to distribute oil. 6. Replace parts. REPLACE SPARK PLUG Replace spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Ignition timing is fixed, nonadjustable. NOTE: ...