HVI CERTIFIED 120 Volts, 0.25 amps, 60 hz. Grill White, polymeric grill secured in place with torsion springs; easily removed if necessary, dimensions - 11" x 133/4". Blower Wheel Balanced polymeric dual inlet blower wheel 513/32" dia. x 4" depth, 30 paddles, secured in place using 8M hex nut. Motor Enclosed 4 pole electronically balanced permanently split capacitor motor (PSC); Thermally protected and life time lubricated. Motor bearings - ball. Rated 115/120 volts, 60 Hz, 0.25 amps. Fan

HVI CERTIFIED 120 Volts, 0.20 amps, 60 hz. Grill White, polymeric grill secured in place with torsion springs; easily removed if necessary, dimensions - 11" x 133/4". Blower Wheel One piece polymeric centrifugal blower wheel, 57/32" diameter, 229/32" wide, with 30 paddles. Motor Heavy duty, permanently split capacitor, plug-in, 4 pole motor, life time lubrication, suitable for continuous operation. Rated 120 volts, 60 hz., 0.20 amps. Fan Housing 23 gauge galvanized steel housing. Dimens

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: 5. Sufficient air is needed for proper combustion and exhausting of gases WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND through the flue (chimney) of fuel burnin

IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. NOTE: This unit includes a side access panel for wiring that does not require the removal of the fan’s blower assembly. If you choose to wire the unit from the inside, you will need to remove the blower assembly and internal wiring compartment. Both methods are equally effective. 1a. External Wire Compartment: Remove the wire compartment cover screw and place cover in a secure plac

Connect the ground wire from the house to the Green wire from the fan’s receptacle (Figure 8). Use approved methods for all connections. 4. Restore power and test your installation. NOTE: The fan’s receptacle wires might need to be pulled outside compartment for connection. Only pull the three loose wires outside of compartment. Additional wires will be present. Figure 8 Ground Hot (Black) White Supply from house SECTION 7 Use and Care CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BE

PROTEGEZ VOUS-MEME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SECURITE. FAILLIR A SE CONFORMER AUX INSTRUCTIONS PEUT RESULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE A LA PROPRIETE. CONSERVER CES INSTRUCTIONS POUR REFERENCES FUTURES. INSTRUCTIONS GENERALES DE SECURITE Lors de l’utilisation d’appareils electriques, des precautions de base doivent toujours etre suivies pour reduire les risques d’incendie, de choc electrique et de blessures corporelles, incluant ce qui suit: 1. Bien l

Figure 1 Figure 2 210952009 Rev. B 2-06 2 of 8 Joist Housing Hanger Bar Figure 3 Joist 1b. Internal Wire Compartment: Remove the screw holding the venturi 4. Carefully tuck wire back inside wire compartment and replace wire in place. Lift the venturi up and at an angle to slide it out of the compartment cover securing with the screw that was removed earlier. housing (Figure 6). Remove the wire compartment cover screw and place the cover in a secure place (Figure 7). SECTION 6 NOTE: If the fan mo

Push the grill up into position (Figure 10). Figure 10 Trouble Probable Cause Suggested Remedy 1. Fan does not operate when the switch is on. 2. Fan is operating, but air moves slower than normal. 3. Fan is operating louder than normal. 1a. A fuse may be blown or a circuit tripped. 1b. Connector plug from motor is not plugged in. 1c. Wiring is not connected properly. 1d. Motor has stopped operating. 2. Obstruction in the exhaust ducting. 3a. Motor is loose. 3b. Fan blade is hitting housing of un

Choose the location for your fan. To ensure the best air and sound performance, it is recommended that the length of ducting and the number of elbows be kept to a minimum, and that insulated hard ducting be used. Larger duct sizes will reduce noise and airflow restrictions. This fan will require at least 8" of clearance in the ceiling or wall, and will mount through drywall up to 3/4" thick. The fan mounts between 16" or 24" on center joists using the 4 provided mounting rails. 3. Select the mos

Install transformer into hood canopy by lining up the 2 holes on the flange of the transformer with the 2 screw studs in the top left side of the hood canopy. Use 2 of the included 8-32 screws to make the connection and fully tighten (Figure 1). Figure 3 Keyholes Stud w/Hex Nuts Screw Stud Figure 1 Transformer Rear Wall 2.Attach the capacitor to the blower by lining up the two holes on the flange of the capacitor with the holes on the blower. Use the 2 included #6 screws to make the connection a