091-0058 SNAPPER * 1189 Old Schuylkill Road * P.O. Box 111 * Parker Ford, PA 19457-0111 PHONE: (610) 495-7181 * * * FAX: (610) 495-5951 Form SLB514 694 LEAF BLOWER SLB514 OWNER’S MANUAL Assembly Instructions Your leaf blower has been carefully packed at the factory. Before proceeding with assembly, make sure all parts have been received and are in good condition. If there are shortages or damage, report it immediately to the company from whom you obtained the machine. (Note: In the follo

Small stones, twigs, or grit can be thrown with sufficient force to cause injury or damage. 4. When running machine, DO NOT PUT HANDS OR FEET INTO INLET OR OUTLET because the rotating impeller can cause injury. 5. Never start engine or use blower without impeller cover mounted in place. Do not put any objects like sticks or fingers in holes of impeller cover. 6. Stop the engine and disconnect the spark plug wire before attempting to clean obstructions or blockage from the intake or discharge

IMPROPER OPERATION CAN CAUSE SERIOUS INJURY. CAUTION \ DO NOT REMOVE IMPELLER 5 COVER WHILE MACHINE IS V RUNNING. SEVERE INJURY i WILL RESULT. 5 TJFJrjrjr.ArW.WJTJF; PART NO. 091-0059 CAUTION ! |1) READ OPERATING INSTRUCTIONS THOROUGHLY BEFORE USING. A (2) DAN6ER: Rotating parts. Keep hands, feet, and clothing out of openings at all a times and especially while machine is running. y ~ (3) NEVER operate with the impeller housing cover removed. ^ (4) NEVER direct the discharge air stream

Box 111 * Parker Ford, PA 19457-0111 Phone: (610) 495-7181 or (800) 348-1117, Fax: (610) 495-5951 McDonough, GA., 30253 U.S.A. COPYRIGHT ©1999 SNAPPER INC. ALL RIGHTS RESERVED MANUAL No. 0-6168 (f.R. 08/02/99) MANUAL No. 06168 2 LEAF BLOWER PART NO. Item No. SLB552PN PART NO. SLB862IC Quantity Description 1 705-0088 2 703-0108 3 090-0457 4 705-0028-2 5 090-0091 6 705-0044 7 705-0034 8 705-0002 9 090-0057 10 703-0422 11 090-0031 12 703-0415 13A 090-0090 13B 14 703-0424

Shaft Key Engine Housing 5/16-24 x 3/4" HHCS Pltd 5/16" Split Lockwasher Pltd Impeller 3/8-24 x 1-1/4" HHCS Pltd Housing Spacer Front Housing 5/16-18 x 5/8" HHCS Pltd 5/16-18x1-1/2" HHCS Pltd Impeller Cover Chute Weld Assembly Diverter Weld Assembly 3/8" Internal Lockwasher Pltd. Vinyl Grip, Diverter Handle Diverter Clip 1/4-20 x 1/2" HHCS Pltd 1/4" Split Lockwasher Pltd 1/4" Flat Washer Pltd Spring, Diverter 1/4-20 x 5" Lg. Carriage Bolt 1/4-20 x 6" Lg. Carriage Bolt Defle

NOTE: The following procedure can be performed with the mower installed on the tractor, however for ease of installation, removing the mower deck is recommended Install Hook Plate 1. Remove the right side belt cover and retain taptite screws. 2. Remove the deflector, spring, and hinge assemble. Retain the hardware except for the carriage bolts. Use a hammer to drive the carriage bolts back through the deck, and discard the bolts. 3. Install the hook plate (B, Figure 1) below the stone guard usin

No. 1693706, 1695299 For 54” Mower Decks Instructions Read these safety rules, and the safety rules in your tractor Operator’s Manual, and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. THE TRIANGLE SIGNIFIES IMPORTANT CAUTIONS OR WARN- INGS WHICH MUST BE FOLLOWED. WARNING .When blower assembly is removed from the mower deck, the deflector must be properly installed. .If the mowe

ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves. AVERTISSEMENT: Veuillez lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de securite. Tout defaut de le faire pourrait entrainer des blessures graves. Electrolux Home Products 104Warren Road Augusta, GA 30907 Copyright E2004 Electrolux Home Products, Inc. 530163810 2/2/04 Instruction Manual Manua

To unfold, loosen two handle knobs and rotate up to the operating position. The upper handles are secured with four knobs. Insert two 5/16-18 x 2 curved head bolts through the handles directly below the two shipping knobs. Place one internal tooth lock washer on each of the bolts. Thread knobs onto curved head bolts. Tighten all four knobs securely. Assembly complete. Your unit is now ready to be started and checked for proper operation. Some minor final adjustments may be required; see the Main

As an owner of off-road gasoline or diesel engine equipment and/or as an employer, you also may have an obligation under the California Occupational Safety and Health Act or under Proposition 65 to warn persons exposed to gas and diesel engine exhaust and/or other Proposition 65 chemicals in and around your workplace. See California Health and Safety Code section 25249.5, Title 22 of the California Code of Regulations at Section 1200 er seq., and Title 8 of the California Code of Regulations Sec