Évaluations - 2, GPA: 5 ( )

Fabricant : Lanier Taille : 4.08 mb Nom Fichier : Langue d'enseignement:

Make sure the paper is placed correctly so that it is fed straight. *5 It is recommended to place one sheet at a time. *6 The paper tray fence is fixed. If you wish to change the size of paper placed in this tray, contact your service representative. *7 When loading paper, make sure that the stack height does not exceed the lower limit mark of the paper tray 2. . p.160 “Setting special paper in the Paper Tray 2” *8 When the paper size is larger than A4L, you can load 10 sheets. When the paper size is smaller than A4L, you can load 100 sheets. *9 When the thick papersizeis largerthanA4L, you can load 10 sheets.When the thick paper size is smaller than A4L, you can load 40 sheets. *10 When loading copy paper, make sure that the stack height does not exceed the limit mark. The maximum number of sheets you can load at a time depends on the paper thickness and condition. *11 If you wish to copy onto thick (105g/m2, 28 lb or heavier) paper, select Thick Paper mode. . "Special Paper Indication" in the System Settings manual *12 Paper size up to 600mm(23.6") is available when an optional HDD is installed. Important . If you use damp or curled paper, staples may become jammed or a misfeed may occur. Note . When loading copy paper in the paper tray 1-4 and the large capacity tray (LCT), place the copy side of the paper face up. . When loading copy paper in the bypass tray, place the copy side of the paper face down. . When you use the bypass tray, it is recommended to set the copy paper direction to L. . Postcards and envelopes should be fed from the paper tray 2 or the bypass tray. . Some kinds of envelopes might cause misfeeds and wrinkles. In this case, push down the green lever of the fusing unit.. p.65 “When copying onto envelopes” . Envelopes with large flaps should be fed from the paper tray 2 or a misfeed might occur. See the illustration below. 24 2 Copy Paper . If youloadpaper of thesamesizeinthe same directionintwo or more trays, the machine automatically shifts to the other tray when the first tray in use runs out of paper. This function is called Auto Tray Switching. (However, if thePaper Type of onetray isrecycled orspecial paper, thesettings ofthe other trays must be the same for Auto Tray Switching.) It saves interrupting a copy run to replenish paper when making a large number of copies. . p.41 “Selecting Copy Paper”, . p.184 “Auto Tray Switching” . The paper types you can select in System Settings are only general classifications. The copy quality for every kind of paper in a classification is not guaranteed. See . p.26 “Non-recommended Paper” for more information. Direction-fixed paper or 2-sided paper Direction-fixed (top to bottom) or 2-sided paper (e.g., letterhead paper, punched paper, or copied paper) might not be printed correctly depending on how the originals and paper are placed. Set "Letterhead setting" in system settings, and then place the original and paper as shown below. . “Letterhead Setting” on p.204 “Input/Output” Basics Non-recommended Paper RCAUTION: • Donotusealuminumfoil,carbonpaper,orsimilarconductivepapertoavoid afireorequipmentfailure. Important . Do notuse anyofthe followingkinds of paper or a faultmight occur. • Thermal fax paper • Art paper • Aluminum foil • Carbon paper • Conductive paper • OHP transparencies for color copying • Paper with perforated lines • Hemmed paper . Do not copy on the side of paper that has been already copied on or a fault might occur. Note . Do not use the following kinds of paper or a misfeed might occur. • Bent, folded, or creased paper • Torn paper • Slippery paper • Perforated paper • Rough paper • Thin paper that has low stiffness • Paper with a lot of paper dust on its surface . If you make a copy on rough grain paper, the copy image might be blurred. . Do not use paper that has been already copied or printed on or a fault might occur. Paper Storage Note . When storing paper, the following precautions should always be followed: • Do not store paper where it will be exposed to direct sunlight. • Avoid storing paper in humid areas (humidity: 70% or less). • Store on a flat surface. . Under high temperature and high humidity conditions or low temperature and low humidity conditions, store paper in a vinyl bag. Toner Toner Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. Our products are engineered to meet high standards of quality and functionality, and we recommend that you only use the expendable supplies available at an authorized dealer. Handling Toner Important . If you use toner other than the recommended type, a fault might occur. Reference If you want to add toner. . p.162 “D Adding Toner” Toner Storage When storing toner, the following precautions should always be followed: • Store toner containers in a cool, dry place free from direct sunlight. • Store on a flat surface. Used Toner Note . Toner...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :