User Counter Clears the counter which was set by the user. 03 System Count System Count. Displays the total amount of scanned documents up to now. Imprinter menu Depending on the setting on the “Counter setting menu”, the page number of the scanned document will be printed. The imprint unit (KV-SS010) is required. If a host computer is connected, there may be settings required on the host computer as well. No. Item LCD Content Page 01 Setting the imprinter data Pre Imprint Allows for the selection of the printing content using an imprinter. The imprinter will print on the printing (front) side of the document scanned. 28 02 Setting the imprinter position Pre Position Allows for the selection of the printing position using an imprinter. 03 Setting the imprinter font style Pre Font Alows for the selection of the printing font style using an imprinter. 04 Setting the imprinter orientation Pre Rotate Allows for the selection of the printing orientation using an imprinter. 29 Display Panel Instructions Others menu No. Item LCD Content Page 01 Checking the version Version Displays the firmware version of the mechanical control, pre-imprinter or post-imprinter. If an optional imprinter is not installed, the imprinter version will not be displayed. 30 02 Setting the buzzer Buzzer Selects whether the buzzer is turned on or off. If selection is in the “ON” position: When pressing a key, one short beep will be heard. When there is an error, 5 short beep will be heard. When scanning is completed correctly, one long beep will be heard. 03 Setting the SCSI ID SCSI ID Sets the SCSI ID No. 04 Setting the terminator Terminator Set “Enable” or “Disable”. “Enable”: If last device on chain “Disable”: If between devices 05 Setting the transfer rate Transfer Rate • Changes the maximum value of the synchronous transfer rate of the SCSI interface. • Lower the synchronous transfer rate to 10 Mbytes/ sec. if the computer has failed to recognize the scanner or the scanner fails to operate properly. 06 Checking the roller cleaning warning Clean Roller The alarm tells you it is time to check roller. If it is near 100%, clean the roller. See “Cleaning the Unit” on page 44. 31 Clearing the roller cleaning warning Clean Roller Clear the “Clean Roller Warning ..%” display. 07 Checking the roller modules replacement warning Replace Roll. The alarm tells you the roller needs to be changed. If it is near 100%, replace the paper feed roller module and retard roller module. See “Replacing Consumable” on page 52. Clearing the roller modules replacement warning Replace Roll. Clear the “Replace Roll. Warning ..%” display. 08 Setting the product ID Product ID Selects the product ID. The product ID setting depends on the host computer scanner application you are using. Allows scanner to emulate other Panasonic scanner. 32 09 Setting the sleep mode Sleep Mode Sets the time until sleep mode turns ON. Display Panel Instructions .Operation 1,4 4 1 1 Press the menu key until the desired menu is displayed. • The SCAN, COUNTER, IMPRINT and OTHERS keys are used as a menu key. • When pressing the SCAN key, the display will appear as shown in the diagram on the right. 2 Use the 3 key or the 4 key to select the desired item. • The display at the right is an example of a setting for the scanning setting mode. 3 Use the 1 key or the 2 key to select the desired content. • The display on the right is an example of a setting for the back side contrast. 4 Press the HOME key to return to the “Ready” display or another menu key to go to another menu. SCAN COUNTER IMPRINT OTHERS READY/ ERROR STOP/START MODE SELECT HOME 3 2Menu keys (ex. SCAN) 01 .F.Br i ghtness D––––+––––L Hos t 07 .B.Con tras t L––––+––––H Hos t 07 .B.Con tras t L––] –+––––H L2 Ready 01 .Di sp .Counter Scan When the HOME key is pressed : When the COUNTER key is pressed for another menu key : ¤In steps 2 or 3, you can change to the desired menu by pressing the desired menu key. ¤See pages 22 to 33 for details. ¤For changing the display language, see page 16. Display Panel Instructions . Actual settings Scan setting menu (by pressing the SCAN key) Number, mode and default display • Pressing the 3 key will change to the next mode. • Pressing the 4 key will change to the previous mode. Contents • Pressing the 1key or the 2 key will change to another value. 01 Front side brightness 0 1 .F. B r i g htn e s s D ssssrssss L Ho s t • When “Host” is displayed, pressing the 1 key or the 2key will change the display to “Norm”. • “D” means dark. “L” means light. D4 D2D3 D1 Norm Host L4L3L2L1 02 Front side image emphasis 0 2 .F. E m p sssrs Ho s t h a sis • When “Host” is displayed, pressing the 1 key or the 2key will change the display to “Medium”. NoneSmooth Low Medium Host High 03 Front side contrast 0 3 .F. C o n tr a s t L ssssrssssH Ho s t • When “Host” is displayed, pressing the 1 key or the 2key will change the display to “Norm”. • “H” means high. “L” means low. L4 L2L3 L1 Norm Host H4H3H2H1 • For changing ...