Évaluations - , GPA:
(
)
)
Fabricant : Dell
Taille : 3.51 mb
Nom Fichier : e52bfae7-ca84-4c4c-91b7-89aa8b22f06f.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Print Cartridge Holder 3. Remove by pulling the tape seal that is affixed to the print cartridge holder and the paper guide. 4. Pinch slightly together the handles of the closing lever to release it from its cartridge tray holder and turn it upwards to open the tray holder. 5. Remove the new print cartridge from its pouch. 6. Remove protection tape from the print cartridge. ATTENTION Do not touch the metal part of the cartridge nor put the tape back on again. 7. Insert the print cartridge into the holder as shown below. ATTENTION Be careful not to let the print cartridge touch or catch on to the print circuit film. 8. Lower the handle lever until it locks in and fixes the cartridge in place. 9. Position the print cartridge holder along where the document will pass through. • The print will be located on the page properly for your application. fi-565PR Imprinter Operator’s Guide | 7 10. Close the print cartridge cover. 2.3. Operating Test After installing the imprinter, test to see if printing can be performed on the Offline Print Test mode. 1. While pressing the [Function] button (.. or ..) on the operator panel, switch on the scanner. Continue pressing on the [Function] button. 2. Release the [Function] button when the Function Number Display changes from [P] to [b]. Function Send to Scan Function Function Function Number Display [Function] button 3. Place a blank document on the ADF paper chute. ATTENTION . Use A4 or Letter size paper. If the size is smaller than A4 or Letter, printing may not successfully complete. . Confirm that the Print Cartridge is positioned within the document width. 4. Press [Scan] button to test. .. Paper will feed into the ADF, and the Imprinter will print out the Print Test Characters starting at 5mm from the paper’s edge. HINT Print test patterns Test pattern 1 (Horizontal): ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000 Test pattern 2 (Horizontal): abcdefghijklmnopqrstuvwxyz{|}~ 00000000 Test pattern 3 (Horizontal): !”#$%&()*+,-./0123456789:;<=>?@00000000 Test pattern 4(Vertical): ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000 Test pattern 5 (Vertical): abcdefghijklmnopqrstuvwxyz{|}~ 00000000 Test pattern 6 (Vertical): !”#$%&()*+,-./0123456789:;<=>?@00000000 When multiple sheets of documents are placed in the ADF, the Test Print repeats patterns from 1 through 6. The numbering data portion “00000000” changes from 0 (Zero) with increment of 1(one). (One test pattern is printed at a time. Press the [Scan] button to continue printing the next test pattern.) Print Test Sample 5. To stop Offline Print test mode, turn off the Scanner. 5mm Feeding direction 8 | 3. Basic Operation 3. Basic Operation 3.1. Positioning the Print Cartridge To Position the print cartridge for printing: 1. Open the Print Cartridge Cover. 2. Slide the print cartridge holder, as below, to the left or right within the document width to set it at a suitable print starting position. HINT . The small “^” protruding from the upper right hand side of the print cartridge tray handle indicates the beginning print position on the page. . Above the print cartridge tray are document paper size markings; please use them to adjust for printing positions. . Put the actual document in the ADF and confirm that the print cartridge is positioned within the document’s width. 3.2. How to Use the Paper Guides Use the Paper Guides to prevent against paper jams due to curling of the edges, as shown below. Feed direction Place the Paper Guides at the ends where the paper edges will pass through. 1. Insert the document in the scanner. 2. Open the Print Cartridge Cover. 3. Slide the Paper Guides to the left and right of the page edges. HINT When you wish to print on the near the edges of a wide width paper, remove the Paper Guide in order to open space for the Print Cartridge, and attach it at the center. For Right Side Edge Printing Paper Guide For Left Side Edge Printing ATTENTION Be careful not to let the Paper Guide touch or catch onto the print circuit film. fi-565PR Imprinter Operator’s Guide | 9 To Remove the Paper Guides Pressing and holding together with your fingers, as below, lift up and pull away the guide. Paper Guide To Attach the Paper Guides 1. The Paper Guides should be in place as in the picture on the left. 2. The top portion of the guide should be pushed in to fit tightly. Paper Guide 3.3. Print Setup You can configure settings for the imprinter by using the scanner driver dialog box. FUJITSU TWAIN driver (Example) Click [Option] button. In [Option] dialog box, choose [Imprinter (Endorser)] tab and specify the Imprinter settings. HINT Available items are: • Y offset (Printing) • Font orientation • Strings definition (Max. 40 characters) • Counter Setup (column, add/subtract, step) For the details, please refer to “FUJITSU TWAIN 32 Scanner Driver User’s Guide” or “TWAIN Driver Help” Paper Guide 10 | 3.4. Replacing the Print Cartridge Replace the Print Cartridge as follows: ATTENTION • When the following message appears, replac...