Évaluations - 3, GPA: 3.7 ( )

Fabricant : Cannon Taille : 286.61 kb Nom Fichier : Langue d'enseignement:

Step 5 Release all buttons. The timer display will revert to the time of day with the ‘Auto’ symbol lit & ‘cookpot‘ symbol remaining lit. At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent audible tone will be heard. The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to flash until the timer is returned to Manual operation (see below). Step 6 Press the Manual button. The audible tone will be cancelled and the oven(s) will be returned to Manual. Step 7 Turn the oven control(s) to the OFF position. Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day. Step 2 Place food onto the correct shelf position in the oven and close the oven door(s). Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven function. NOTE: The Cookpot symbol disappears OVEN TIMER OPERATION TO CANCEL AN AUTO COOKING PROGRAMME BEFORE THE COOK PERIOD HAS FINISHED. Step 1 Turn the oven control(s) to the OFF position. Step 2 Press the Manual button to return the oven(s) to “Manual” operation. The ‘Auto’ symbol will go out. Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing the Cook Period button. OTHER NOTES ON TIMER OPERATION 1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook Period button. 2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time button. 3. Having set a Cook Period and End Time an electronic device stores the information. The device within the timer will switch the oven(s) on and off at the required times. 4. When setting an Auto Cooking Programme and a mistake is made, to clear:– (a) Press & release the Manual button. (b) Start the sequence again. 5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity supply to the oven has been interrupted. Reset the timer to the correct time of day. Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated and completely cooked. 6. To set each function always press and hold the required function button and at the same time press “+” or “–” buttons. HOTPLATE The hotplate has one dual control wok burner, one large high speed burner, three normal simmering burners and one small simmering burner. The dual control wok burner consists of a smaller inner and a larger outer burner that can operate either together or separately. Use of the two burners together with large pans on maximum setting gives a very high input and reduces cooking times with respect to conventional burners. Use of the two burners together provides a more uniform distribution of heat on the bottom of the pan. Cookware of all sizes can be used above the dual control wok burner. For small pans it is recommended that only the inner burner is used. .. . The knob situated below the symbol on the fascia panel operates the outer burner. .. . .. . The knob situated below the symbol on the fascia panel operates the inner burner. . . The two normal simmering burners on the right hand side of the hotplate are oval in form and can be turned through 90°. This makes the hotplate more flexible in how it can be used. For cooking fish or heating oval cookware use the two burners with their longest sides at 90° to the front of the hotplate. When using the griddle or for heating rectangular, square or large cookware use the two burners with their longest sides parallel to the front of the hotplate. For medium size cookware use any of the two burners in any orientation. All pans should be placed centrally over the burners. TO USE THE HOTPLATE 1. Press the ignition button and then push in and turn the control knob of the chosen burner anti-clockwise to the large flame symbol. Continue to press the ignition button until the spark lights the gas. When operating the dual control burner there is a separate control knob for the inner and outer burners. 2. Turn the control knob anti-clockwise to the desired setting. Only turn the control knob between the large flame symbol and the small flame symbol for adjusting the setting. 3. To turn off, turn the control knob fully clockwise to the O position. DO NOT use mis-shapen pans which may be unstable. DO NOT use round base woks directly on the pan supports. Each burner is fitted with a spark ignition electrode for lighting the gas. To ensure rapid lighting of the burners every time they are used, the electrodes must be kept clean and dry. Remove any food spillage or cleaning materials from the electrodes using a small nylon brush such as a tooth brush. Access to the ignitor can be achieved by lifting off the loose burner parts carefully when the burners are cool. If aluminium based pans are used, a silvery deposit may appear on the top edge of the pan support fingers. See ‘Care and Cleaning’ section for further infor...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :