Évaluations - , GPA: ( )

Instructions Avet Reels, Modèle AUTO-REWIND AIR HOSE REEL 95211

Fabricant : Avet Reels
Taille : 2.89 mb
Nom Fichier : 95211.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

b. To decrease tension, unwrap the hose one time from the drum. 3. Run the hose back through the guide and re-attach the hose stopper. 4. Pull the Hose out several feet to check the tension. CautiOn: When adding wraps of hose, do not exceed the winding mechanism’s spring capacity. Add just enough wraps of hose to achieve the desired tension. Damage to the winding mechanism will result if spring is over-tensioned. General Operating instructions 1. Check the Wheel operation by slowly pulling the Hose out. You should hear a clicking noise. 2. To lock the Hose, pull it out a minimum of 1/2 revolution and it will stay locked after the first, second, or third click. 3. To unlock, slowly pull until the clicking stops, and let it retract until the Hose Stopper hits the Hose Guide. CautiOn: Hold on to the Hose while it is rewinding to avoid damage to the Hose Reel. 4. Attach a coupler (sold separately) to your air compressor hose and apply thread seal tape to the Inlet fitting on the Reel. Connect the coupler to the Inlet fitting. 5. Connect your air tool to the other end of the Hose using another coupler and thread seal tape. 6. Follow all instructions from the air tool and compressor for set up and use. 7. When finished using the Hose, disconnect the air tool and retract the hose. Wipe the Hose Reel clean with a dry cloth. SaFetYOPeRatiOnmaintenanCe SetuP Operating instructions Read the entiRe imPORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired. adjust the Spring tension 1. Pull out approximately six feet of Hose. 2. Remove the Hose Stopper from the Hose and slide the Hose out of the Roller Guide so the Hose is hanging loose. a. To increase tension, wrap the loose hose one time around the Reel Drum. b. To decrease tension, unwrap the hose one time from the drum. 3. Run the hose back through the guide and re-attach the hose stopper. 4. Pull the Hose out several feet to check the tension. CautiOn: When adding wraps of hose, do not exceed the winding mechanism’s spring capacity. Add just enough wraps of hose to achieve the desired tension. Damage to the winding mechanism will result if spring is over-tensioned. General Operating instructions 1. Check the Wheel operation by slowly pulling the Hose out. You should hear a clicking noise. 2. To lock the Hose, pull it out a minimum of 1/2 revolution and it will stay locked after the first, second, or third click. 3. To unlock, slowly pull until the clicking stops, and let it retract until the Hose Stopper hits the Hose Guide. CautiOn: Hold on to the Hose while it is rewinding to avoid damage to the Hose Reel. 4. Attach a coupler (sold separately) to your air compressor hose and apply thread seal tape to the Inlet fitting on the Reel. Connect the coupler to the Inlet fitting. 5. Connect your air tool to the other end of the Hose using another coupler and thread seal tape. 6. Follow all instructions from the air tool and compressor for set up and use. 7. When finished using the Hose, disconnect the air tool and retract the hose. Wipe the Hose Reel clean with a dry cloth. SaFetYOPeRatiOnmaintenanCe SetuP Page 6 For technical questions, please call 1-800-444-3353. Item 95211 user-maintenance instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. tO PRevent SeRiOuS injuRY: Detach air supply from this product before performing any inspection, maintenance, or cleaning procedures. tO PRevent SeRiOuS injuRY FROm tOOl FailuRe: Do not use damaged equipment. if abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use. Cleaning, maintenance, and lubrication note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the Hose Reel. 1. BeFORe eaCh uSe, inspect the general condition of the tool. Check for: • loose hardware or housing, • misalignment or binding of moving parts, • cracked or broken parts, and • any other condition that may affect its safe operation. 2. aFteR eaCh uSe, re-wind the hose onto the reel and wipe the Hose Reel clean with a dry cloth. WaRninG! Internal spring is not user- serviceable or user-replaceable. hose Replacement 1. Remove the Hose Stopper from the hose and set aside. 2. Pull out the old Hose leaving two to three feet on the Reel. Lock the Hose (See General Operating Instructions). 3. Disconnect the old hose from the swivel joint and remove the hose completely. 4. Run the new hose through the Roller Guide. 5. Use thread seal tape on the hose fitting threads and screw the fitting onto the swivel and tighten. 6. Attach the Hose Stopper on the end of the Hose near the Outlet fitting. 7. Carefully release the Drum Latch and allow the Hose to wind onto the reel, evenly distr...