Log:
Évaluations - 2, GPA: 3 ( )

Instructions Buhler, Modèle 90

Fabricant : Buhler
Taille : 1.28 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


TURN IGNITION SWITCH KEY (IF SO EQUIPPED) TO k “OFF” POSITION AND REMOVE KEY FROM SWITCH. THIS WILL REDUCE THE POSSIBILITY OF UNAUTHORIZED STARTING OF ENGINE WHILE _EQUIPMENT ¡S NOT ¡N USE._ A NEVER STORE ENGINE WITH FUEL IN TANK INDOORS OR IN ENCLOSED, POORLY VENTILATED AREAS, WHERE FUEL FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT AS ON A FURNACE, WATER HEATER CLOTHES DRYER OR OTHER GAS APPLIANCE. WARNING: TEMPERATURE OF MUFFLER AND NEARBY > AREAS MAY EXCEED 150°F (65°C). AVOID THESE AREAS. © ENGINE OIL LEVEL: Wipe all snow and moisture from engine in vicinity of control lever and choke. Check oil level every five (5) operating hours or each time enoine is used. See “TO FILL OIL SUMP OR CHECK OIL LEVEL” on Page 2. CHANGE OIL: Change oil after first two (2) operating hours and every 25 operating hours thereafter, more often if operated in extremely dusty or dirty conditions. Change oil while engine is still warm from recent running. A. Clean area around oil drain plug. B. Position equipment so engine oil drain plug is lowest point on engine (see Figure 1). C. Remove oil drain plug and oil fill plug to drain oil. D. Replace oil drain plug and tighten securely. E. Fill oil sump with recommended oil. See “OIL & FUEL RECOMMENDATIONS” and“TOFILLOILSUMPOR CHECK OIL LEVEL” on Page 2. F. Replace oil fill plug and tighten securely. G. Wipe up any spilled oil. SPARK PLUG (seQ Figure 6): This spark ignition system meets all requirements of the Canadian Interference-Causing Equipment Regulations. This engine complies with all current Australian and New Zealand limitations regarding electromagnetic interference. Check spark plug yearly or every 100 operating hours. A. Clean area around spark plug base. B. Remove and inspect spark plug. C. Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use Champion RN4C or equivalent. NOTE: A resistor spark plug must be used for replacement. D. Check electrode gap with wire feeler gauge and set gap at .030 if necessary. E. install spark plug in engine and tighten securely. ELECTRODES ft Mit*» .030 GAP PORCELAIN Figure 6 ® CHECK ENGINE AND EQUIPMENT OFFEN FOR LOOSE NUTS, A BOLTS AND ATTACHMENTS AND KEEP THESE ITEMS TIGHTENED. Page 4 181-1170-14 ADJUSTMENTS STORAGE (Continued) DO NOT MAKE UNNECESSARY ADJUSTMENTS. FACTORY (D DRAIN CARBURETOR: SETTINGS ARE SATISFACTORY FOR MOST APPLICATIONS AND Drain carburetor by pressing upward on bowl drain (see Figure CONDITIONS. IF ADJUSTMENTS ARE NEEDED, PROCEED AS 7) which is located below carburetor cover (see Figure 1). FOl! nws ------------ A DRAIN FUEL INTO APPROVED CONTAINER OUTDOORS, „ MSk AWAY FROM OPEN FLAME. BE SURE ENGINE IS COOL. DO CARBURETOR: I NOT SMOKE. If you think your carburetor needs adjusting, see your nearest AUTHORIZED TECUMSEH SERVICE OUTLET. Engine performance should not be affected at altitudes up to 7,000 feet. For operation at higher elevations, contact your AUTHORIZED TECUMSEH SERVICE OUTLET. (D ENGINE SPEED: A NEVER TAMPER WITH ENGINE GOVERNOR WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING ENGINE ABOVE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. CHANGING OF ENGINE GOVERNED SPEED WILL VO...

Ce manuel est également adapté pour les modèles :
Souffleuse à neige - 100 (1.28 mb)
Souffleuse à neige - 130 (1.28 mb)
Souffleuse à neige - OHSK80 (1.28 mb)
Souffleuse à neige - 100 (1.28 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories