Évaluations - 3, GPA: 3.7 ( )

Fabricant : Buhler Taille : 1.84 mb Nom Fichier : Langue d'enseignement:

Afterward, continue reading instructions below. • Change oil after first 2 operating hours and every 25 operating hours thereafter. Engine should still be warm but NOT hot from recent use. NOTES To check oil on engines with an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions on page 5. To check oil on engines with an oil fill cap/plug, see "II. Oil Fill Cap/Plug" instructions on page 5. Figure 35. Disconnecting/Connecting Spark Plug Figure 36. Typical Spark Plug Connection Figure 37. Electric Starter Connections 1. Power Cord to Outlet 2. Switch Box 3. Starter Button 4. Schuko Plug 5. Power Cord to Switch Box on Engine 6. Electric Starter Switch Box on Engine 1 5 2 3 120V A.C. 1 5 2 3 4 220V A.C. 6 181-1275-14 4-Cycle • Snow King Engine Page 17 I. Oil Fill Cap/Dipstick If your engine has an oil fill cap/dipstick go to step 1. If your engine does NOT have an oil fill cap/dipstick, see "II. Oil Fill Cap/Plug" instructions on page 20. 1. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 38 and 39. See "G. Avoid Accidental Starts" instructions on page 2. Afterward, continue reading instructions below. • Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. • Carefully attach the spark plug wire to the grounding post, if provided. 2. Be sure fuel fill cap is on and tightened securely. See Figure 40. See Figure 14 on page 7. Afterward, continue reading instructions below. File was named: 181-1275-14MY060105x.fm 3. Be sure you find the correct oil drain plug location, if present (see equipment manufacturer’s instructions). See Figure 41. See Figure 14 on page 7. Afterward, continue reading instructions below. 4. Clean area around oil drain plug. Figure 38. Disconnecting/Connecting Spark Plug Figure 39. Typical Spark Plug Connection Figure 40. Fuel Fill Cap Figure 41. Oil Fill/Drain Locations STOPSTOP1. Oil Fill Cap/Dipstick 2. Oil Fill cap/Plug 3. Oil Drain Plug 1 3 2 3 Back View 2 33 Page 18 4-Cycle • Snow King Engine 181-1275-14 181-1275-14 4-Cycle • Snow King Engine Page 19 5. Place approved recyclable oil container under oil drain plug, if present. See Figure 41 on page 18. Afterward, continue reading instructions below. 6. Remove oil drain plug, if present. 7. Tip engine to position the oil flow, so it will drain from the lowest point on the engine (see equipment manufacturer’s instructions). 8. Drain oil into an approved recyclable oil container. NOTE Used oil must be disposed of at a proper collection center. 9. Install oil drain plug and tighten securely. 10. Clean area around oil drain plug. See Figure 41 on page 18. Afterward, continue reading instructions below. 11. Remove oil fill cap/dipstick. See Figure 42. 12. Fill with recommended oil. See Figure 43. See "III. Oil and Fuel Specifications" instructions on page 4. See Table 1 on page 4. Afterward, continue reading instructions below. NOTES DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. DO NOT allow oil level to fall below the “ADD” mark on oil fill cap/dipstick. Doing so may result in equipment malfunction or damage. Contact your Authorized Tecumseh Servicing Dealer for Tecumseh Oil. 13. Wipe away any spilled oil. 14. Install oil fill cap/dipstick. Tighten securely. See Figure 42. 15. Carefully disconnect spark plug wire from grounding post, if provided. See Figures 38 and 39 on page 18. See "G. Avoid Accidental Starts" instructions on page 2. Afterward, continue reading instructions below. 16. Carefully re-connect spark plug wire to spark plug. See Figures 38 and 39 on page 18. Figure 42. Oil Fill Cap/Dipstick Locations Figure 43. Engine Oil Level OH318SA/OH358SA OH195SA/OH195SP LH195SA/LH195SP LH318SA/LH358SA FULL ADD OK Fill Between “FULL” and “ADD” Marks File was named: 181-1275-14MY060105x.fm II. Oil Fill Cap/Plug If your engine does NOT have an oil fill cap/dipstick, go to step 1. If your engine has an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions on page 18. Figure 44. Disconnecting/Connecting Spark Plug 1. Carefully disconnect spark plug wire and keep it away from spark plug. See Figures 44 and 45. See "G. Avoid Accidental Starts" instructions on page 2. Afterward, continue reading instructions below. • Keep the disconnected spark plug wire securely away from metal parts where arcing could occur. • Carefully attach the spark plug wire to the grounding post, if provided. Figure 45. Typical Spark Plug Connection File wa...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :