Évaluations - , GPA: ( )

Instructions Honda Power Equipment, Modèle OMGX10902 I0

Fabricant : Honda Power Equipment
Taille : 827.95 kb
Nom Fichier : 50240299-d502-4f82-98aa-37cbda60032b.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Operating - 9 TROUBLESHOOTING Using Troubleshooting Chart If you are experiencing a problem that is not listed in this chart, see your Authorized Service Center for service. When you have checked all the possible causes listed and you are still experiencing the problem, see your Authorized Service Center. IF CHECK Engine Lugs Down Run engine at full throttle. Blade angle. Raise blade to float position. Adjust skid shoes. Blade Digs In Too Deep Raise blade to float position. Adjust skid shoes. Rear Wheels Slip Add rear weights and chains. Troubleshooting - 10 STORAGE Storing Blade Clean the blade with water under pressure. If possible, store blade indoors on hard, level surface. If you store blade outside: • Put blocks of wood or a board under blade. • Cover blade with a waterproof cover. Inspect blade. Repair or replace badly worn or damaged parts. Check all bolts, nuts, and pins to make sure they are secure. Apply touch-up paint where needed to prevent rust. Oil all pivot points so that they will work freely. Grease blade pivot plate, thrust channel, pivot plate reinforcement and pivot release bracket. Storage - 11 ASSEMBLY Box of Parts Bag of Parts M92899 I B A C D E F G H J L K P R S O M N Q T U A B C D E F G H I J K L M N O P Q R S T U Qty 2 1 1 1 1 Key Description Blade Assembly Pivot Plate Rear Mounting Bracket Lift Channel Pivot Control Handle Pivot Handle Support (2) Rear Support Channel Thrust Channel Blade Pivot Bracket Front Stabilizer Bracket Pivot Release Rod (2) Strap (2) Front Stabilizer Pin (2) Spacer (2) Lift Link Pivot Plate Reinforcement Pivot Control Rod Pivot Release Bracket Rear Locating Bracket (2) Lift Arm Drawbar Support Plate Operator’s Manual Bag of Parts Description Return Spring Full Thread Bolt Rubber Handle Grip Idler Spring Spacer Size 3/8 x 4-1/2 in. 3/8 x 1/2 x 1/4 in. Assembly - 12 ASSEMBLY Qty Description Size 2 Flat Washer 5/16 Flat 3 Cotter Pin .094 x.75 1 Flat Washer 1/2 x 2 in. 2 Flat Washer 3/8 x 1-1/2 in. 4 Hex Head Bolt 5/16 x 1-1/4 in. 2 Hex Head Bolt 5/16 x 5/8 in. 4 Hex Head Bolt 5/16 x 2-1/2 in. 3 Flat Washer 3/8 x 1 in. 3 Lock Washer 3/8 in. 1 Nylock Nut 5/8 in. 1 Eye Bolt 3/8 x 2 in. 6 Hex Lock Nut 5/16 in. 1 Hex Head Bolt 5/8 x 1-3/4 in. 2 Hex Head Bolt 1/2 x 1in. 8 Spring Locking Pin .095 DIA x 1-5/8 in. 1 Spring Locking Pin 0.148 DIA x 2-7/8 in. 1 Flat Washer 21/32 x 1-5/16 in. 1 Hitch Pin 5/8 x 1-7/8 in. 2 Spring Clip .065 DIA x.72 in. OD 1 Full Thread Bolt 3/8 x 2-1/2 in. 2 Hex Lock Nut 1/2 in. 2 Flat Washer 1/2 x 1-1/2 x 3/16 in. 8 Nut/Lock Washer Assembly 5/16 in. 13 Hex Head Bolt 3/8 x 1 in. 18 Nylock Nut 3/8 in. 3 Hex Nut 3/8 in. Grease Use a SAE Multi-purpose grease based on the expected air temperature range during the service interval. Install Drawbar Support Plate A B D C 1. Place drawbar support plate (A) under rear axle and under drawbar (B). 2. Align drawbar holes with axle holes. 3. Install four 5/16 x 2-1/2 in. hex head bolts (C) and four 5/ 16 in. lock nuts (D). Install Parts to Blade Assembly 1. Assemble spring anchor bolts: a. Turn one 5/16 in. nut and lock washer assembly (B) onto the 5/16 x 1-1/4 in. hex head bolt (A) with lock M93033B B A C D E washer away from the head of the bolt. b. Insert the bolt and nut assembly (A & B) through hole in rib of blade assembly then assemble with a second 5/ 16 in. nut and lock washer assembly (C) onto bolt (A). c. Adjust inside nut and lock washer (B) flush with end of thread on bolt then tighten nut and lock washer (C) against blade rib. d. Assemble second 5/16 x 1-1/4 in. bolt to opposite side of blade assembly using the same procedure. Assembly - 13 ASSEMBLY 2. Assemble breakover stop bolt: Assemble Pivot Release Bracket, Pivot Plate, • Install one 5/16 x 5/8 in. hex bolt (D) into bottom hole and Thrust Channel of each rib on blade assembly and fasten with 5/16 in. lock nut (E). Assemble Pivot Plate to Thrust Channel M93 035 A B C D E F M93 036 B A D J F G H D E C I 1. Assemble the pivot plate (A) and the pivot plate reinforcement (B) on top of the thrust channel (C). 2. Lubricate thrust channel, pivot plate, and pivot plate reinforcement in areas of contact with light multi-purpose grease. 3. Insert 5/8 x 1-3/4 in. hex head bolt (D) through the pivot plate reinforcement, pivot plate, and the thrust channel and fasten with 21/32 x 1-5/16 in. flat washer (E) and 5/8 in. nylock nut (F). 4. Loosen 5/8 in. nylock nut approximately 1/4 turn to allow the assembly to pivot freely. 1. Lubricate large hole and two faces of pivot release bracket (A) with light multi-purpose grease. 2. Assemble idler spring (B) into smallest hole of pivot release bracket (A). 3. Place 3/8 in. lock washer (C), 3/8 x 1-1/2 in. flat washer (D), pivot release bracket (A), large 1/2 x 2 in. flat washer (F), and spacer (E) onto 3/8 x 2-1/2 in. full thread bolt (G). NOTE: Make sure pivot release bracket and large 1/2 x 2 in. flat washer (F) pivot freely after bolt is tight. 4. Align holes in thrust channel (H) with pivot plate rei...