Évaluations - 3, GPA: 4.7 ( )

Fabricant : Honda Power Equipment Taille : 3.92 mb Nom Fichier : Langue d'enseignement:

The OPEN position provides the correct fuel mixture for operation after starting, and for restarting a warm engine. CHOKE KNOB CLOSED OPEN Shift Lever The shift lever selects F (FORWARD), N (NEUTRAL), or R (REVERSE). The shift lever also controls the transmission drive ratio; moving the lever farther from NEUTRAL increases drive speed. While clearing snow, use the shift lever to control drive speed, so you can leave the throttle lever in the FAST position for best snow-clearing performance. R (Reverse) N (Neutral) SHIFT LEVER F (Forward) .. .. .. 14 CONTROLS & FEATURES Discharge Deflector Lever Foot Pedal (track type only) HIGH AND FAR LOW AND NEAR HIGH AND FAR LOW AND NEAR DISCHARGE DEFLECTOR DISCHARGE DEFLECTOR LEVER FOOT PEDAL HIGH MIDDLE LOW The discharge deflector lever controls the snow discharge angle. HIGH Deep snow or for transporting the snowblower. MIDDLE Normal use. LOW Smooth, ice-covered surfaces only. Use the pedal for adjusting the height and angle of the machine in relation to the tracks. Hold the handles and step on the pedal. Raise or lower the machine to the desired position and release the pedal. CONTROLS & FEATURE S Drive Clutch Lever and Auger Clutch Lever Use these controls to engage the snow blowing mechanism and/or the drive mechanism. AUGER CLUTCH LEVER DRIVE CLUTCH LEVER Squeeze to engage the Squeeze to engage the snow blowing mechanism. drive transmission. When both levers are squeezed, the drive clutch lever locks the auger clutch lever down. Releasing the drive clutch lever then unlocks and releases the auger clutch lever. DRIVE CLUTCH LEVER LOCKED The auger clutch lever remains locked down as Both levers squeezed long as one hand continues to squeeze the drive clutch lever. CONTROLS & FEATURES Transmission Release Lever The transmission release lever has two positions, RELEASED and ENGAGED. Set the lever in the ENGAGED position for self-propelled operation. Set it in the RELEASED position when pushing the snowblower with the engine stopped. Operatingthetransmissionreleaseleverwhiletheengineisrunning candamagethetransmission. 1. Stop the engine. 2. Set the shift lever in the ‘‘N’’ (Neutral) position. 3. Set the lever in the ENGAGED or RELEASED position. Pushingortowingthesnowblowerwiththetransmissionrelease controlintheengagedpositionwilldamagethehydrostatic transmission. RELEASED ENGAGED TRANSMISSION RELEASE LEVER CONTROLS & FEATURES FEATURES Work Light HS1132 Standard HS724, HS928 Optional Kit The light comes ON while the engine is running, and it goes OFF when the engine stops. The light does not come ON when the engine switch is turned ON unless the engine is started. The light can be adjusted up or down. Snow Clearing Bar (equipped type) If the snow discharge chute or snow blowing mechanism becomes restricted, stop the engine and use this bar to remove the obstruction. After clearing the obstruction, wipe the bar clean, and store it in the holders. Before removing the obstruction, be sure to stop the engine, and make sure that all rotating parts have come to a complete stop. Remove the spark plug cap from the spark plug. WORK LIGHT SNOW CLEARING BAR HOLDERS BEFORE OPERATION BEFORE OPERATION Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the snowblower and its operation before you begin using it. Know how to quickly shut off the snowblower in case of an emergency. IS YOUR SNOWBLOWER READY TO GO? For your safety, and to maximize the service life of your equipment, it is very important to take a few moments before you operate the snowblower to check its condition. Be sure to take care of any problem you find, or have your servicing dealer correct it, before you operate the snowblower. Improperly maintaining this snowblower, or failing to correct a problem before operation, could cause a malfunction in which you could be seriously injured. Always perform a pre-operation inspection before each operation, and correct any problem. Before beginning your pre-operation checks, be sure the snowblower is on a level surface and the engine switch is in the OFF position. BEFORE OPERATION Check the General Condition of the Snowblower: Look around and underneath the snowblower for signs of oil or gasoline leaks. Check the auger house and the discharge chute for accumulation of packed snow or ice. Clean the auger housing and discharge chute before starting the snowblower. Look for signs of damage. Check each control for proper operation. Check the auger and blower for loose or broken bolts. If broken, replace them with new ones (page 49 ). Check the skid shoes and scraper for wear. Replace them if necessary (page 50 ). Check that all nuts, bolts, screws are tightened. Check the Engine Check the oil level (page 40 ). Check the fuel level (page 38). Starting with a full tank will help to eliminate or red...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :