Log:
Évaluations - 3, GPA: 4.3 ( )

Instructions Snapper, Modèle 1380

Fabricant : Snapper
Taille : 2.29 mb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


5. To lower the height of the scraper bar, raise the skid shoes. 6. If the scraper bar becomes worn, it can be replaced by removing the hardware attaching it to the snowthrower. A B Figure 3. Chute Deflector Adjustment (Some Models) A. Chute Deflector Knob B. Chute Deflector Figure 5. Skid Shoe Adjustment A. Scraper Bar B. Skid Shoe C. Nuts Figure 4. Remote Deflector Control (Some Models) A. Maximum Throwing Position B. Spring C. Control Handle C A A B C B 13 Operation FULL TRACTION Easy Turn™ Lever Released Both Wheels Drive Figure 6. Easy Turn Control EASY TURN™ FREEWHEELING AND TRACTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 6). Engaging the Easy Turn™ lever releases the right traction wheel but allows the left wheel to continue driving (Figure 6). Releasing the Easy Turn™ lever automatically engages both drive wheels for full traction. NOTE: The Easy Turn™ lever will be more difficult to activate under a heavy load. Activate the lever before beginning a turn. When Pushing the Snowthrower: For easy turning when pushing the snowthrower, disengage the right wheel using the traction lock pin (See Figure 7.) 1. Turn the unit off, remove the engine key, and disconnect the spark plug wire. EASY TURN™ TRACTION Easy Turn™ Lever Engaged Right Wheel Freewheels, Left Wheel Drives A B Figure 7. Traction Drive Lock A. Pin in Outer Hole (Freewheel) B. Pin in Inner Hole (Drive) 2. To DISENGAGE the traction drive lock, insert the Traction Lock Pin through the outer hole in the right axle. The unit can now be pushed with minimal resistance. 3. To ENGAGE the traction drive lock, align the hole in the hub with the inner hole in the axle, and install the Traction Lock Pin. NOTE: Be sure both wheels are locked (locking pin in inner hole) when clearing snow. 14 Storage AFTER EACH USE Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls.Heat from the engine will usually prevent the snow from freezing solid while the unit is running, but after the engine is shut down, some snow may continue melting from engine heat, and later freeze around some moving parts as the unit cools. After each period of use, follow these steps to prevent freeze-up caused by ice formationin and around the engine controls and external parts. 1. Before shutting off the engine, pull the starter rope out 2 - 3 times, and allow it to rewind slowly. This will help clear packed snow from the starter cord area. Allow the engine to run for several minutes. 2. Stop the engine by moving the throttle lever (See Figure 1) down, or by pulling out the engine key. 3. Brush snow and ice from the snowthrower. Be sure to clear engine and snowthrower controls, discharge chute, worm and chute rod gears, clutch cable areas, and anywhere else snow has accumulated. 4. Always remove the engine key and store in a safe place to prevent unauthorized use. 5. If the snowthrower is kept in a cold shelter, fill the fuel tank to prevent condensation. Do not store near sparks or flame. Note: The Engine Owner’s Manual contains further information on preventing ice formation and freeze-up. WARNING Never store the unit, with gasoline in engine or fuel tank, in a heated shelter or in enclosed, poorly ventilated enclosures. Gasoline fumes may reach an open flame, spark or pilot light (such as a furnace, water heater, clothes dryer, etc.) and cause an explosion. Handle gasoline carefully. It is highly flammable and careless use could result in serious fire damage to your person or property. Drain fuel into an approved container outdoors away from open flame or sparks. STORAGE WARNING Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel vapor is also toxic to humans and animals. Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps: • Disengage the PTO, set the parking brake, and remove the key. • Perform engine maintenance and storage measures listed in the engine owner’s manual. This includes draining the fuel system, or adding stabilizer to the fuel (do not store a fueled unit in an enclosed structure - see warning). Before starting the unit after it has been stored: • Check all fluid levels. Check all maintenance items. • Perform all recommended checks and procedures found in the engine owner’s manual. • Allow the engine to warm up for several minutes before use. 15 16 Regular Maintenance AUGER GEAR CASE LUBRICATION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (A, Figure 9). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add The Dealer Line Winter Weight Worm Gear Oil (available from your dealer). 4. Re-install pipe plug, an...

Ce manuel est également adapté pour les modèles :
Souffleuse à neige - 10528 (2.29 mb)
Souffleuse à neige - 11532 (2.29 mb)
Souffleuse à neige - 11570 (2.29 mb)
Souffleuse à neige - 1338 (2.29 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories