Évaluations - 1, GPA: 5 ( )

Fabricant : Bolens Taille : 2.68 mb Nom Fichier : Langue d'enseignement:

20. Use only attachments and accessories approved by the manufacturer. Failure to do so, can result in personal injury. 21. If situations occur which are not covered in this manual, use care and good judgment. Contact your dealer or telephone 1-800-800-7310 for assistance and the name of your nearest servicing dealer. Maintenance & Storage 1. Never tamper with safety devices. Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the tines and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or over- speed the engine. The governor controls the maximum safe operating speed of the engine. 5. Maintain or replace safety and instruction labels, as necessary. 6. Follow this manual for safe loading, unloading, transporting, and storage of this machine. 7. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc. 8. Always refer to the operator’s manual for proper instructions on off-season storage. 9. If the fuel tank has to be drained, do this outdoors. 10. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. Your Responsibility 1. Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. 2. The safety label on the tiller is reproduced below for your review. To ensure safe operation of the tiller, follow the instructions on all labels closely. 4 5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: This operator’s manual covers various models of tillers. The units illustrated may vary slightly from your unit. Follow only those instructions which pertain to your model number. NOTE: References to right or left side of the tiller are determined from behind the unit in the operating position. To Remove Unit From Carton • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. • Remove loose parts included with unit (i.e., operator’s manual, etc.). • Cut corners and lay carton down flat. • Remove packing material. • Roll or slide unit out of carton. Check carton thoroughly for loose parts. • Extend control cable and lay on the floor. Be careful not to bend or kink control cable. IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. Loose Parts In Carton Tailpiece and Depth Stake NOTE: All hardware needed for assembly is attached to the loose parts or the tiller. Before Assembly WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. Assembling The Handle • Remove the handle adjustment lever from handle and lift up upper handle to raise in operating position. See Figure 1. • Reinsert adjustment lever through the lower hole, tightening the lever into lock nut on the retainer bracket. • Once the lever is in the lock nut, the handle can be moved to the desired position and then tighten securely. Attaching Tailpiece and Depth Stake • Remove the two self-tapping screws on the frame and slide the tailpiece into the frame, with the lower hole in the tailpiece toward the front. See Figure 2. • Secure tailpiece with the screws just removed. Figure 1 Figure 2 Handle Adjustment Lever Handle Adjustment Lever Retainer Bracket Lock Nut Tailpiece Self-Tapping Screws Lower Hole 6 Check Cable Adjustment • With the clutch lever disengaged, pull starter rope slowly several times. The tines should not turn. If they turn, the cable is not adjusted properly. • To adjust the cable, loosen the nut near the top of the cable and unscrew the cable to provide additional slack in wire. See Figure 3. • Tighten the nut and check again for proper adjustment. Figure 3 SECTION 3: KNOW YOUR TILLER Figure 4 WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Tine Clutch Control The clutch control lever is located on the left handle. Squeezing the lever against the handle engages the tine drive. Release the lever to stop the tines from turning. See Figure 4 Depth Stake The depth stake is located in the rear of the tiller and it controls the tilling depth. See Figure 4 Handle Adjustment Lever The handle may be adjusted to the height desired. Loosen the handle adjustment lever a few turns and pivot handle up or down to desired position. Tighten lock. See Figure 4. Throttle Control The throttle control lever is located on the engine. It controls the engine’s speed and stops the engine. • With the thrott...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :