Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Never attempt to clean snow from excessively steep slopes. The maximum slope for any opera tion is 17.7% (10’). CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place. and all nuts, bolts and clips are secure. 2. Check the engine oil level. See your engine Owner’s Manual for procedure and specifications. 3. Check the fuel supply. Fill the tank to within l/4 to i/2 inch of top of tank to provide space for expansion. See your engine Owner’s Manual for fuel recommendations. with care. Never fill the tank when the engine is hot or runnmg. Always move outdoors to fill the tank. 1 flame spark. .; Keep snowthrower and gasoline away from open 4. Position the deflector at the desired angle and the scraper bar at the desired height. 5. Check the auger control clutch lever (A, figure l), drive control clutch lever (B, figure 1) and discharge chute deflector (D, figure 1) for proper operation. If adjustment is required, sea the Service Section for procedures. 6. Check the discharge chute control rod (C, figure 1) for proper function. Check to make sure sprocket teeth on lower chute control rod fully engage holes in flange around bottom of discharge chute. The bracket that holds lower chute control rod is slotted and can be moved up or down to obtain full engagement of sprocket teeth. 7. Check shift lever (E, figure 5) for proper position. If adjustment is required, see SHIFT CONTROL ADJUSTMENT in the Service Section. 8. Check to make sure spark plug wire is attached and spark plug is tightened securely into engine. If necessary, torque spark plug to 15 ft. Ibs. 9. After servicing engine and before beginning snow removal, check controls again with engine running. STARTING THE ENGINE 1. Move the ground speed shift lever (E, figure 5) to the Neutral position. 2. Turn the fuel valve (G, figure 5) to the ON position. 3. Insert the ignition key (C, figure 5) into the ignition switch and push fully in to the RUN position. 4. Move the throttle lever (D, figure 5) fully up to the FAST position. 4. Turn the choke knob (B, figure 5) fully counterclockwise if engine is cold. Do not choke a warm engine. 5. Push the primer button (A, figure 5) two times if engine is cold. Do not prime a warm engine. 6. Pull starter handle (F, figure 5) rapidly or push starter button if equipped with the electric start. Do not allow starter handle to snap back. Let the starter rope rewind slowly while keeping a firm hold of the starter handle. 6 Operation 7. As the engine warms up and begins to operate evenly, turn the choke knob slowly counterclockwise to the OFF position. If engine falters, return to l/2 choke position until it runs smoothly, then turn it to the choke OFF position. NOTE: Allow the engine to warm up for a few minutes before operating the snowthrower. Engine will not develop full power until it reaches operating temperature. 8. Run the engine at or near top speed during snowthrower operation. OPERATING THE SNOWTHROWER 1. Position the discharge chute to the desired angle and direction. 2. Set the ground speed control lever to the desired forward or reverse position. 3. Press the auger clutch lever on the right-hand grip to begin auger rotation. 4. Press the drive clutch lever on the left-hand grip to begin moving the snowthrower. 5. To disengage the drive mechanism, release both clutch levers. Set the ground speed control lever to the NEUTRAL position. NOTE: After a normal break-in period of 2 - 4 hours of use, it may be necessary to adjust the drive belt. See DRIVE BELTS in the Service Section for the adjustment procedure, AFTER EACH USE 1. Before stopping engine, pull the starter rope twice and allow it to rewind slowly, then stop the engine by moving the throttle lever (D, figure 5) all the way down or by pulling out on the ignition key. This will prevent freeze-up. 2. The engine Owner’s Manual contains further information on preventing engine freeze-up. 3. Always remove the key to prevent unauthorized use. Figure 5. Engine Controls A. Primer Button D. Throttle Lever B. Choke Knob E. Shift Lever C. Ignition Key/Switch F. Starter Handle G. Fuel Valve 4. Clean snow and ice from the snowthrower. 5. If the snowthrower is kept in a cold shelter, fill the fuel tank to prevent condensation. Do not store near sparks or flame. A WARNING Never store snowthrower, with gasoline in engine or fuel tank, in a heated shelter or in enclosed, poorly ventilated enclosures. Gasoline fumes may reach an open flame, spark or pilot light (such as a furnace, water heater, clothes dryer, etc.) and cause an explosion. Handle gasoline carefully. It is highly flammable and careless use could result in serious fire damage to your person or property. Drain fuel into an approved container outdoors away from open flame or sparks. 7 Regular Maintenance NORMAL CARE I I Every 25 Care Reauired See Paae Hours -a Check auger gear case lubrication.* Page 8 . I Lubricate snowthrower. Paae9 I . 1 Check tire pressure. I Paae 9 I l I 1 Change engine oil.**+ ...
Ce manuel est également adapté pour les modèles :Souffleuse à neige - 1691413 (341.84 kb)
Souffleuse à neige - 1691411 (341.84 kb)