Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Look for this symbol to point out important safety precautions. It mean--Attention!! Become alert!! Your safety is involved. SHOWN ACTUAL SIZE H \ \ _J Two shear bolts (R) and hex lock NOT SHOWN ACTUAL SIZE nuts (S) are provided as replacement parts for the spiral _ jT augers. Store in a safe place until needed. (See page 16.) REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A 2 Hex Bolt, 3/8" x 1-1/2" M 2 Bowed Washer B 12 Hex Bolt, 3/8" x 1" N 6 Washer, 1/4" C 2 Hex Bolt, 5/16" x 1-3/4" O 2 Washer, 5/16" D 6 Hex Bolt, 1/4" x 1" P 2 Washer, 3/4" E 2 Carriage Bolt, 5/16" x 1-3/4" Q 4 Hairpin Clip, 1/8" F 6 Carriage Bolt, 5/16" x 1" R 2 Shear Bolt G 2 Shoulder Bolt S 2 Hex Lock Nut, 5/16" H 10 Hex Nut, 5/16" T 1 Tarp Strap I 6 Flanged Lock Nut, 1/4" U 3 Chute Keeper J 12 Hex Lock Nut, 3/8" V 1 Plastic Grip K 10 Lock Washer, 5/16" W 2 Lock Pin L 18 Lock Washer, 3/8" 4 CARTON CONTENTS 1. Frame Bracket, R.H. 2. Frame Bracket, L.H. 3. Hanger Bracket, L.H. 4. Hanger Bracket, R.H. 5. Side Plate, L.H. 6. Side Plate, R.H. 7. Cross Brace 8. Plastic Weight Keg 9. Weight Tray 1 2 14 10. Side Brace Arms (2) 11. Chute Crank Assembly 12. Lift Handle with Cable 13. Clutch/Idler Assembly 14. Drive "V" Belt 15. Auger "V" Bett (Attached to Housing Assembly) 16. Anti-rotation Bracket 17. Chute and Control Cable Assembly 18. Housing Assembly Hardware Package (Stored inside Plastic Keg) TOOLS REQUIRED FOR ASSEMBLY ASSEMBLING PARTS TO TRACTOR FRAME (2) 7/16" Wrenches Right hand (R.H.) and left hand (L.H.) are determined (2) 1/2" Wrenches from the operators position while seated on the tractor. (2) 9/16" Wrenches (t) 5/8" Wrench or Adjustable Wrench (t)11/16" Wrench or Adjustable Wrench (t) 3/4" Wrench or Adjustable Wrench (t) Knife General Purpose Grease REMOVAL OF PARTS FROM CARTON • Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 4 and 5. & & CAUTION: Before starting to assemble the snow thrower, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition. TRACTOR PREPARATION Before proceeding with these instructions, refer to the Service and Adjustments section of your tractor owner's manual for specific safety instructions. • Allow engine, muffler and exhaust deflector to cool before beginning. • Remove any front or rear attachment which is mounted to your tractor. • Remove the mower deck. Refer to your tractor owner's manual for removal instructions. Mark all loose parts and save for reassembly. • Remove the tractor hood and grill assembly. Refer to your tractor owner's manual for removal instructions. ITEMS REMOVED FROM TRACTOR Store all brackets and fasteners removed from the tractor during the assembly of the snow thrower, unless the instructions call for their use. • Remove the hex bolt from the threaded hole at the top front corner of R.H. front suspension bracket. Remove the nut from the carriage bolt at the top rear corner of the bracket, leaving the carriage bolt in the tractor frame. See figure 1. • Repeat for the L.H. front suspension bracket. REMOVE BOLT REMOVE NUT \ \\ FRONT SUSPENSION BRACKET (R.H.) / / Y FIGURE 1 RIGHT SIDE VIEW • Attach the rear of the R.H. side plate to the tractor using the original carriage bolt and a new 3/8" lock washer and 3/8" lock nut. Attach the front of the side plate to the threaded hole in the tractor frame using a 3/8" x 1" hex bolt and a 3/8" lock washer. Repeat for the L.H. side. See figure 2. NOTE: If the side plates are removed from the tractor frame, be sure to reassemble bolts and nuts back into the frame. 318" LOCK 3/8" I-_X WASHER LOCK-NUT 3/8" x 1" HEX BOLT / SIDE PLATE (R.H.) / FIGURE 2 RIGHT SIDE VIEW 6 • Remove the mower stop bracket and its two bolts and nuts from the R.H. side of the tractor frame as shown in figure 3. • If the tractor has a muffler guard at the front of the R.H. foot rest, remove the bottom bolt and nut, and the washer which is located between the guard and the tractor frame. See figure 3. • Remove the two bolts from the bottom of both the R.H. and L.H. foot rests. See figure 3. MUFFLER GUARD _ (ONLY MODELS WITH SIDE MUFFLER) MOWER STOP i BRACKET // FIGURE 3 RIGHT SIDE VIEW Assemble the R.H. hanger bracket to the bottom hole where the mower stop bracket was removed and to the bottom hole under the front of the foot rest. Fasten with two 3/8" x 1" hex bolts, 3/8" lock washers and 3/8" hex lock nuts. (On tractors with muffler guards, slide the hanger bracket between the guard and the tractor frame.) See figure 4. MUFFLER GUARD (ONLY MODELS WITH SIDE MUFFLER) R.H. HANGER BRACKET 3/8" x 1" HEX BOLT HEX 3/8" LOCK LOCK NUT WASHER Assemble the L.H. hanger bracket to the left side of the tractor frame using two 3/8" x 1" hex bolts, two 3/8" lock washers and two 3/8" hex lock nuts as shown in figure 5. \ \ LH. HANGER 3/8" LOCK BRACKET WASHER 3/8" x 1" HEX BOLT FIGURE 5 LEFT SIDE VIEW • Assemble the L.H. frame bracket (with bend) to the L.H. f...