14 727291 SCREW, 5/16-18 x .63 15 727940 SCREW, 1/4-20 x 2.00 16 727517 PLATE, Mounting Support 17 722305 SUPPORT, Frame 18 722320 FRAME, R.H. 19 722633 SCREW, 5/16-18 x 3/4 20 1740032 RING, Foam 21 724068 CLAMP, Fuel Line, Screw Type 22 723210 SCREW, 1/4-20 x 5/8 Footnotes: 522 SINGLE STAGE SNOW THROWER Manual No. 7006053 SERIES 0 TP 400-5245-IR-SX-N 13 Engine Drive System Group Manual No. 7006053 522 SINGLE STAGE SNOW THROWER TP 400-5245-IR-SX-N SERIES 0 14 Engine Drive System Group Item Part

7006053 Copyright © 2006 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision IR, 11/22/2006 TP 400-5245-IR-SX-N Table Of Contents s PAGE GROUP 4 Handle Assembly Group 6 Body Covering Group 8 Auger and Housing Group 10 Chute System Group 12 Frame and Fuel Tank Group 14 Engine Drive System Group 18 Wheel Assembly Group 20 Electric Starter Group 22 Decals Group 522 SINGLE STAGE SNOW THROWER Manual No. 7006053 SERIES 0 TP 400-5245-IR-SX-N 3 Handle Assembly Group Manual No.

If done, the flywheel may shatter during operation. Do not tamper with links or other parts to increase engine speed. Regular maintenance improves performance and extends engine life. More frequent service is required when operating in adverse conditions. See any authorized service dealer for correct replacement parts. Other parts may not perform as well, may damage the engine, result in injury, or void your warranty. Inspect / Change Spark Plug (^Fig. 7^) Annually or every 50 hours of use

MS-3395-5/05 PRINTED IN U.S.A. Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed /Gr'') by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer. Figures (Example: Fig.

. Fill tank to approximately 3.8 cm (1-1/2 in.) O below top of neck to allow for fuel expansion. If fuel spills, wait until it evaporates before starting engine. Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. STARTING ENGINE Fig. 4 CAUTION: The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will

Install the downward pressure lock plate (E) OR place the lift link (D) in snowthrower position. 4. Install the lift lever extension (C). 5. Install the lift rod and attachment (Figure 10). Figure 11. Normal Installation & Removal B C D E F A. Hitch Rod B. Hitch Rod C. Lift Lever Extension D. Lift Link (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Snowthrower Position A 8 Sub-Frame Hitch Installation Instructions A F C D G A B C D E Snowthrower & Dozer Applications Mower Applications A B C

Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D F E Figure 7. Install Lock Plate - Hydraulic Lift Models A. Lift Cylinder D. Lock Plate B. Flat Head Pin (Original) E. Hair Pin Clips C. Flat Head Pin (New) F. Lift Shaft Assy. 5 6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E.

WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When starting the engine, ensure that spark plug, muffler, fuel cap and air cleaner are in place and secured. Do not crank engine with spark plug removed. If engine floods, set choke (if equipped) to open/run position. WARNING Engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. When starting the

. 19. Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition. EMISSIONS 1. Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm. 2. If available, look for the relevant Emissions Durability Period and Air Index information on the engine emissions label. IGNITION SYSTEM 1. This spark ignition system complies with Canadian ICES-002. 5 6