Step 6. Ensure the Anti-drip Juice Spout is pushed down into the pouring position. Step 7. Place a suitable sized glass or jug underneath the Juice Spout. ASSEMBLING YOUR BREVILLE 800 CLASS CITRUS PRESS 8 9 OPERATING YOUR BREVILLE 800 CLASS™ CITRUS PRESS OPERATING YOUR BREVILLE 800 CLASS™ CITRUS PRESS Operating Step 1. Ensure the 800 Class Citrus Press is correctly assembled and a glass or jug is placed under the Juice Spout before juicing commences. Step 2. Cut the citrus fruit in half by cutting across the fruit segments, rather than across the tip ends, to ensure more efficient juicing. Important: Some fruits, such as lemons and tangelos, have knobbly tip ends which require trimming for better contact with the Fruit Dome. Step 3. Plug the power cord into a 230/240v power outlet, switch on at the power outlet then switch the On/Off button to ON. Turn machine main switch ‘On’. OPERATING YOUR BREVILLE 800 CLASS CITRUS PRESS 11 NOTE: The Stainless Steel Filter should be emptied when full with pulp and seeds. The Filter can be emptied during juicing by switching the Citrus Press "OFF" at the On/Off button and carefully removing the Juicing Cone and Filter. Clean and replace Stainless Steel Filter and Juicing Cone before continuing to juice. Do not allow the Stainless Steel Filter to overfill as this may prevent correct operation or damage the unit. Step 4. Place a citrus fruit half, cut side down, onto the Juice Cone and push down lightly onto the spikes Step 5. Grasp the Soft Grip Handle and slowly lower the Juicing Press Arm and press down firmly until the Fruit Dome is in contact with the fruit skin. The motor will automatically start and the Juicing Cone will begin to rotate. The juice will be extracted from the fruit and flow through the Juice Spout into the glass, The pulp and seeds will collect in the Stainless Steel Filter. Step 6. The 800 Class Citrus Press juices very quickly so each fruit half will be juiced in a few seconds. To automatically stop the motor, lift the Juicing Press Arm up and backwards to its extended position. OPERATING YOUR BREVILLE 800 CLASS CITRUS PRESS Step 7. Remove the used fruit from the Juicing Cone. Empty excess pulp and seeds from Stainless Steel Filter as required. Repeat Steps 3-7 to continue juicing. OPERATING YOUR BREVILLE 800 CLASS CITRUS PRESS 12 13 DISASSEMBLING YOUR BREVILLE 800 CLASS™ CITRUS PRESS DISASSEMBLING YOUR BREVILLE 800 CLASS™ CITRUS PRESS Step 1. Step 2. Step 3. Step 4. Storage. Switch the Citrus Press "OFF" at the On/Off Pull the Juicing Press Arm up and backwards, With the arm in the down position, remove Lift the Juice Collector from the Motor Body with Insert the Dust Cover before storing. button, then switch OFF at the power outlet away from the Motor Base, until fully extended. the Fruit Dome by pressing the button marked the Stainless Steel Filter, Juicing Cone and Fruit and unplug. "EJECT". Let the Friut Dome drop onto the Dome still in place. Remove the Cone and Filter Step 2.5 Juicing Cone. from the Juice Collector over a sink for easier Close the anti drip spout by pulling to upper cleaning. position. Follow recommended Care and Cleaning guidelines. 14 DISASSEMBLING YOUR BREVILLE 800 CLASS CITRUS PRESS DISASSEMBLING YOUR BREVILLE 800 CLASS CITRUS PRESS 15 CARE AND CLEANING CARE AND CLEANING Cleaning 16 • Always ensure that the 800 Class Citrus Press is switched OFF at the On/Off button, the power is switched off at the power outlet and the plug is removed from the power outlet before cleaning, disassembling, assembling and storing the appliance. • Follow these instructions to clean all surfaces or parts that come into contact with food during juicing:1. For easy cleaning – immediately after each use rinse removable parts under warm water to remove wet pulp. Allow parts to air dry before reassembling. 2. For thorough cleaning - after disassembling the appliance, all removable parts should be washed in hot soapy water or on the top shelf of the dishwasher. The Motor Base and Juicing Press Arm should be wiped with a soft, damp cloth. All parts should be dried thoroughly before reassembling. • Store the cleaned and reassembled Citrus Press in an upright position in a cool, dry place. Do not place any items on top of the Citrus Press whilst stored. NOTE: Rinse or wash all removable parts immediately after use. Dried citrus pulp is difficult to remove and may stain. If any staining does occur, wipe the affected part/s with undiluted dishwashing liquid, rinse and dry thoroughly. NOTE: Do not soak the Stainless Steel Filters or other removable parts in bleach. Never immerse the motor base in water or any other liquid. Do not use harsh abrasives. CARE AND CLEANING 17 POSSIBLE PROBLEM EASY SOLUTION Will not work Switch not ‘On’ Arm not lowered Cone or Dome not assembled properly Make sure pulp filter is aligned correctly TROUBLE SHOOTING GUIDE TIPS ON JUICING THE INSIDE INFORMATION ON JUICE Although juice drinks are usually developed with flavour, text...