Log:
Évaluations - 3, GPA: 3.7 ( )

Instructions Black Box, Modèle FX810A

Fabricant : Black Box
Taille : 116.8 kb
Nom Fichier :
Langue d'enseignement: enes
Aller à la télécharger



Facilité d'utilisation


Turn the pager OFF. 2. Press and hold the ON/OFF switch, then slide it to the ON position (see ON OFF Figure 5-2. Pager ON/OFF Switch. 22 CAMPUS PAGER 3. Make sure that the Campus Pager is turned ON, then enter a two-digit pager code (00-99) and then 0. 4. Press the TRANSMIT button on the Campus Pager, and the unit will transmit the pager code to the pager. The pager will beep four times, and flash “L” on its display four times. The pager then beeps 12 times and simultaneously flashes 0 on its display to confirm that it received the message code 0. NOTE For example, if you would like the pager to have a new pager code such as 38, enter 380, and press TRANSMIT. After you press the TRANSMIT button, the Campus Pager LED flashes the three digits seven times, and simultaneously transmits the pager code to the pager. The three digits will stay lit until you perform one of the following actions: • Turn the Campus Pager OFF • Press A/C or CANCEL • Transmit a message to a pager Perform the preceding steps for each pager used with the Campus Pager. NOTE If the pager does not successfully store the pager code, repeat the preceding steps. 5.4 Transmitting a Message Code to a Single Pager 1. Turn the Campus Pager power ON. 2. Press A/C or CANCEL if the display shows unwanted pager or message codes. 3. Enter the two-digit code for the pager you want to receive the message, then the one digit message code that you want to send. If you enter the wrong pager or message code, press A/C or CANCEL, then re-enter the correct codes. 23 CAMPUS PAGER NOTE You cannot reset either of these codes after you press the TRANSMIT button. 4. Press the TRANSMIT button. The TRANSMIT display lights during transmission, and the pager’s display flashes the message code number seven times. The three digits will remain lit until you perform one of the following actions: • Turn the Campus Pager OFF • Press A/C or CANCEL • Transmit a message to a pager If desired, press TRANSMIT again to re-send the current message code to the pager. 5. Press A/C or CANCEL, then repeat Steps 3 and 4 if you want to transmit another message code to another pager. 5.5 Transmitting a Message Code to All System Pagers 1. Turn the Campus Pager power ON. 2. Press A/C or CANCEL if the display shows unwanted pager or message codes. 3. Press ALL, then the one digit message codes that you would like to send. If you enter the wrong message code, press A/C or CANCEL, then reenter the correct code. NOTE You cannot reset the message code after you press the TRANSMIT button. 4. Press the TRANSMIT button. The TRANSMIT display lights during transmission, and the pager’s display flashes the message code number. See Section 5.6. If desired, press TRANSMIT again to re-send the current message code. 5. Press A/C or CANCEL, then repeat Steps 3 and 4 if you want to transmit another message code. 24 CAMPUS PAGER 5.6 Receiving a Message Code with the Tone Pager When a Tone Pager is turned ON and receives a page, it sounds 12 beep...

Ce manuel est également adapté pour les modèles :
Téléphones cellulaires - FX800A (116.8 kb)
Téléphones cellulaires - FX800AE (116.8 kb)
Téléphones cellulaires - FX801A (116.8 kb)
Téléphones cellulaires - FX802A (116.8 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories